Reply by Jeff Brower April 19, 20112011-04-19
Uzair-

> actually i have built a C# application on kit.

Can you clarify "on kit"? You build and run a C# application under Linux, right?
Not on the DSK board.

> when i plug my
> kit into Linux and run my exe file, my application send a
> message to check the connections again. means not properly
> detecting the kit.
> so is there a driver problem ?? i have installed the driver
> of usb IC CY7C68001 in WinXP, but i dont have the driver for
> Linux OS for this IC.

Where did you get the WinXP driver? Whoever provides that should be able to provide
a Linux driver, or be able to tell you which Linux distributions include a driver
that is compatible. Did you ask them?

-Jeff

PS. Please post to the group, not to me.
> I am working on TMS C 5416 kit. I have communicated DSP
> 5416(Texas Instruments) with Windows XP OS through usb interface using IC
> CY7C68001(EZ USB SX2) of Cypress Semiconductor coorperation.
>
> Now I want to operate this kit on Linux operating system while using the
same
> usb interface. The Linux OS is not communicating with my kit .What should I
do ?
> what might be the problem ? Have anyone done this ? Any help/guidance `ll be
> highly appreciated.

Well, if it works on Windows then it's gotta work on Linux. Is it the same
box; i.e. a dual boot or virtualized system?

Do you have something else (a 'reference') you can try on your Linux box USB
port? Just something basic, like a
camcorder, smart phone, etc. to make sure the port is enabled and configured
correctly.

How did you test on WinXP? Just using WinXP to recognize the port? Or you
have some application specific software
you can run?

-Jeff

OMAP35x EVM jump-starts low-power apps
The modular and extensible OMAP35x Evaluation Module (EVM) enables developers to start building applications based on the OMAP35x architecture: http://www.DSPRelated.com/omap35x
Reply by Jeff Brower April 19, 20112011-04-19
Pieter-

> I am working on TMS C 5416 kit. I have communicated DSP
> 5416(Texas Instruments) with Windows XP OS through usb interface using IC
> CY7C68001(EZ USB SX2) of Cypress Semiconductor coorperation.
>
> Now I want to operate this kit on Linux operating system while using the same
> usb interface. The Linux OS is not communicating with my kit .What should I do ?
> what might be the problem ? Have anyone done this ? Any help/guidance `ll be
> highly appreciated.

Well, if it works on Windows then it's gotta work on Linux. Is it the same box; i.e. a dual boot or virtualized system?

Do you have something else (a 'reference') you can try on your Linux box USB port? Just something basic, like a
camcorder, smart phone, etc. to make sure the port is enabled and configured correctly.

How did you test on WinXP? Just using WinXP to recognize the port? Or you have some application specific software
you can run?

-Jeff

OMAP35x EVM jump-starts low-power apps
The modular and extensible OMAP35x Evaluation Module (EVM) enables developers to start building applications based on the OMAP35x architecture: http://www.DSPRelated.com/omap35x
Reply by piet...@yahoo.com April 18, 20112011-04-18
Hello All

I am working on TMS C 5416 kit. I have communicated DSP
5416(Texas Instruments) with Windows XP OS through usb interface using IC
CY7C68001(EZ USB SX2) of Cypress Semiconductor coorperation.

Now I want to operate this kit on Linux operating system while using the same
usb interface. The Linux OS is not communicating with my kit .What should I do ?
what might be the problem ? Have anyone done this ? Any help/guidance `ll be
highly appreciated.
please help me as asap.
Regards

pieter

OMAP35x EVM jump-starts low-power apps
The modular and extensible OMAP35x Evaluation Module (EVM) enables developers to start building applications based on the OMAP35x architecture: http://www.DSPRelated.com/omap35x