Manjunath,
A couple of the most common causes of this error are:
1. Incorrect emulation driver selected in cc_setup
2. Incorrect configuration of the driver in cc_setup
Make sure that you use the correct driver for the Signum emulator.
There should be either a special driver that you select in cc_setup OR you
should use the TI C64xx Rev 1.1 XDS510 Emulation driver with a special
configuration file.
Check Signum's instructions or their web site
mikedunn
manjunath <g...@tataelxsi.co.in>
wrote:
Hi Calvin, I would like to have some help from
your side. I am using USB JTAG for debugging the board having TI6415
processors. But the JTAG is from company called Signum. When i start
the CCS 2.2 i am getting the following error. "Error Code :
0x80000240/-180, This was generated by TI's USCIF Driver.. SC_ERR_CTL_NO_TRG_POWER" Even though power is connected to board.
Anyone has encountered this problem and found solution for this. please mail me.
Thanks and regards, Manjunath
-----Original Message----- From: twfoo8x8 [mailto:t...@yahoo.com] Sent: Wednesday, January 14, 2004 6:22 AM To: g...@tataelxsi.co.in Subject: Re: TI DM642Hi all,
Found the solution to this problem.
You must install the SDConfig program found on the TI DM642 installation disk. After that, everything is ok. After
installation, you should get a SDConfig 6000 icon on your desktop.
Installing the SDConfig program from the USB JTAG installation disk is
not enough. After installing this program, you'll get a SDConfig x.xx
icon on your desktop.
Best regards, Calvin Foo --- In
c...@yahoogroups.com, "manjunath" wrote: > Hi, > To
which port you have connected. and also which is the driver u people are > using? > Since i am also using JTAG connected to USB for
debugging . > I think there could be wrong in driver being configured,
but i am not sure. > i think u can look for this bug is in CCS2.2.
check for bug list in the TI > site. > > hope it
may help you people, > Manjunath > > -----Original
Message----- > From: Jean-Michel MERCIER [mailto:jm.mercier@a...] > Sent: Tuesday, January 13, 2004 3:24 PM > To: twfoo8x8;
c...@yahoogroups.com >
Subject: RE: [c6x] TI DM642> > Hello, > > We have the
same problem here. > > Did you found a workaround ? > > Jean-Michel.> > -----Message d'origine----- > > De
: twfoo8x8 [mailto:twfoo8x8@y...] > > Envoy: vendredi 2 janvier
2004 08:32 > > : c...@yahoogroups.com > > Objet : [c6x]
TI DM642 > > > > > > Hiya, > > > > I've purchased the above board and aUSB JTAG. However, I was
not able > > to run the demo. Everything I load the .out file
using CCS 2.20, I > > get the message "does not match target type."
What does this mean? > > > > > > Thank you for
your help. > > > > br, > > twfoo >
> > > > > > > > > > >
_____________________________________ > > Note: If you do a simple
"reply" with your email client, only the > > author of this message
will receive your answer. You need to do > > a "reply all" if you
want your answer to be distributed to the > > entire group. >
> > > _____________________________________ > > About
this discussion group: > > > > To Join: Send an email to
c...@yahoogroups.com > > > > To Post: Send an email to
c...@yahoogroups.com > > > > To Leave: Send an email to
c...@yahoogroups.com > > > > Archives:
http://www.yahoogroups.com/group/c6x > > > > Other Groups:
http://www.dsprelated.com > > > > > > Yahoo!
Groups Links > > > > To visit your group on the web, go
to: > > http://groups.yahoo.com/group/c6x/ > > >
> To unsubscribe from this group, send an email to: > >
c...@yahoogroups.com > > > > > > >
> _____________________________________ > Note: If you do a simple
"reply" with your email client, only the author of > this message
will receive your answer. You need to do a "reply all" if you >
want your answer to be distributed to the entire group. > >
_____________________________________ > About this discussion group: > > To Join: Send an email to c...@yahoogroups.com > > To Post: Send an email to c...@yahoogroups.com > > To
Leave: Send an email to c...@yahoogroups.com > > Archives:
http://www.yahoogroups.com/group/c6x > > Other Groups:
http://www.dsprelated.com> Yahoo! Groups Links > > To visit
your group on the web, go to: >
http://groups.yahoo.com/group/c6x/ > > To unsubscribe from this
group, send an email to: >
c...@yahoogroups.com_____________________________________ Note: If you do a
simple "reply" with your email client, only the author of this message will
receive your answer. You need to do a "reply all" if you want your answer to be
distributed to the entire group.
_____________________________________ About this discussion group:
To Join: Send an email to c...@yahoogroups.com
To Post: Send
an email to c...@yahoogroups.com
To Leave: Send an email to
c...@yahoogroups.com
Archives:
http://www.yahoogroups.com/group/c6x
Other Groups:
http://www.dsprelated.comYahoo! Groups Links
To visit your group on
the web, go to: http://groups.yahoo.com/group/c6x/
To
unsubscribe from this group, send an email to: c...@yahoogroups.com
|