Dear all:
I have purchased two cards one is TMDXEVM5505 ( C55xx ) main processor
card, and other is SpO2 daughter card.
I have checked all example programs on processor card (without
connecting SpO2 daughter card) e.g LCD, UART etc, The board is running
well.
But when i connect the daughter card and want to run any program (that was
running well on standalone card), it failed to run.
Any suggestion?
Thanx in advance
FAYAZ
SpO2 MDK
Started by ●March 15, 2011
Reply by ●March 16, 20112011-03-16
Fayaz-
> I have purchased two cards one is TMDXEVM5505 ( C55xx ) main processor
>
> card, and other is SpO2 daughter card.
>
> I have checked all example programs on processor card (without
>
> connecting SpO2 daughter card) e.g LCD, UART etc, The board is running
>
> well.
>
> But when i connect the daughter card and want to run any program (that was
>
> running well on standalone card), it failed to run.
Can you clarify "failed to run"? There should be some LEDs on the EVM 5505 board that indicate boot status, do these
operate normally? Are you still able to connect CCS and download example programs?
Or does the EVM do nothing that you can see and appears to be dead?
-Jeff
> I have purchased two cards one is TMDXEVM5505 ( C55xx ) main processor
>
> card, and other is SpO2 daughter card.
>
> I have checked all example programs on processor card (without
>
> connecting SpO2 daughter card) e.g LCD, UART etc, The board is running
>
> well.
>
> But when i connect the daughter card and want to run any program (that was
>
> running well on standalone card), it failed to run.
Can you clarify "failed to run"? There should be some LEDs on the EVM 5505 board that indicate boot status, do these
operate normally? Are you still able to connect CCS and download example programs?
Or does the EVM do nothing that you can see and appears to be dead?
-Jeff
Reply by ●March 17, 20112011-03-17
Fayaz-
> There is no indication of failure. The CCS may be connected and
> program may be loaded successfully.
>
> Some there is some garbage type data appear on LCD for running LCD programs.
> As you may know that LCD pins are multiplexed with SPI I2S, which are also used
> for communication with SpO2 AFE.
> But if we use only LCD program, then there is nothing to communicate with AFE.
> Do you think it may be the reason.
Yes, it could be. Is there a signal or pin for the multiplex that you can check with a dig scope? If so this would
be a good thing to do -- see if the value changes when the Sp02 daughtercard is plugged in.
If that is the reason, then you can control the multiplex pin via software. Set for LCD when needed, set for SpO2
when needed.
-Jeff
PS. Please post to the group, not to me.
> On 3/17/11, Jeff Brower wrote:
>> Fayaz-
>>
>>> I have purchased two cards one is TMDXEVM5505 ( C55xx ) main processor
>>>
>>> card, and other is SpO2 daughter card.
>>>
>>> I have checked all example programs on processor card (without
>>>
>>> connecting SpO2 daughter card) e.g LCD, UART etc, The board is running
>>>
>>> well.
>>>
>>> But when i connect the daughter card and want to run any program (that was
>>>
>>> running well on standalone card), it failed to run.
>>
>> Can you clarify "failed to run"? There should be some LEDs on the EVM 5505
>> board that indicate boot status, do these
>> operate normally? Are you still able to connect CCS and download example
>> programs?
>>
>> Or does the EVM do nothing that you can see and appears to be dead?
>>
>> -Jeff
>>
>
> There is no indication of failure. The CCS may be connected and
> program may be loaded successfully.
>
> Some there is some garbage type data appear on LCD for running LCD programs.
> As you may know that LCD pins are multiplexed with SPI I2S, which are also used
> for communication with SpO2 AFE.
> But if we use only LCD program, then there is nothing to communicate with AFE.
> Do you think it may be the reason.
Yes, it could be. Is there a signal or pin for the multiplex that you can check with a dig scope? If so this would
be a good thing to do -- see if the value changes when the Sp02 daughtercard is plugged in.
If that is the reason, then you can control the multiplex pin via software. Set for LCD when needed, set for SpO2
when needed.
-Jeff
PS. Please post to the group, not to me.
> On 3/17/11, Jeff Brower wrote:
>> Fayaz-
>>
>>> I have purchased two cards one is TMDXEVM5505 ( C55xx ) main processor
>>>
>>> card, and other is SpO2 daughter card.
>>>
>>> I have checked all example programs on processor card (without
>>>
>>> connecting SpO2 daughter card) e.g LCD, UART etc, The board is running
>>>
>>> well.
>>>
>>> But when i connect the daughter card and want to run any program (that was
>>>
>>> running well on standalone card), it failed to run.
>>
>> Can you clarify "failed to run"? There should be some LEDs on the EVM 5505
>> board that indicate boot status, do these
>> operate normally? Are you still able to connect CCS and download example
>> programs?
>>
>> Or does the EVM do nothing that you can see and appears to be dead?
>>
>> -Jeff
>>
>