Forums

WINTECH TDS510PLUSE Jtag Emulator

Started by J J April 20, 2010
Dear All
I want program digitalspectrum c6455 DSK with WINTECH TDS510PLUSE Jtag Emulator,
But when I connect board this error display

Error connecting to the target:
Error 0x00000220/-1022
Error during: Execution, OCS,
PTI_ERR_ICE_WAIT_TO Error Occured at 0x00000000
Sequence ID: 0
Error Code: -1022
Error Class: 0x00000220
I/O Port = 240

Board Name: C64xx Rev 1.0 TDS510USB Emulator - WintechDigital
Cpu Name: CPU_1

Abort: Close Code Composer Studio.
Retry: Try to connect to the target again.
Cancel: Remain disconnected from the target
Diagnostic: Run diagnostic utility.

please help me to solve this problem
2 suggestions off hand:

(1). Run the diagnostic utility, as it suggests.

(2). Contact WinTech tech support after you re-check the installation
procedure and any troubleshooting tips that they might have.

That would be probably be the best first steps to take for problem
solving in this case.

g.
On 04/20/2010 08:07 AM, J J wrote:
> Dear All
> I want program digitalspectrum c6455 DSK with WINTECH TDS510PLUSE Jtag
> Emulator,
> But when I connect board this error display
>
> Error connecting to the target:
> Error 0x00000220/-1022
> Error during: Execution, OCS,
> PTI_ERR_ICE_WAIT_TO Error Occured at 0x00000000
> Sequence ID: 0
> Error Code: -1022
> Error Class: 0x00000220
> I/O Port = 240
>
> Board Name: C64xx Rev 1.0 TDS510USB Emulator - WintechDigital
> Cpu Name: CPU_1
>
> Abort: Close Code Composer Studio.
> Retry: Try to connect to the target again.
> Cancel: Remain disconnected from the target
> Diagnostic: Run diagnostic utility.
>
> please help me to solve this problem
> Reply to sender
>
> | Reply to group
>
> | Reply via web post
>
> | Start a New Topic
> Messages in this topic
>
> (1)
> Recent Activity:
>
> * New Members
>
> 3
>
> Visit Your Group
>
J J,

My first guess (and it is only a guess) is there is no power to the target board.

R. Williams

---------- Original Message -----------
From: J J
To: c...
Sent: Tue, 20 Apr 2010 05:07:49 -0700 (PDT)
Subject: [c6x] WINTECH TDS510PLUSE Jtag Emulator

>
>
> Dear All
> I want program digitalspectrum c6455 DSK with WINTECH TDS510PLUSE Jtag Emulator,
> But when I connect board this error display
>
> Error connecting to the target:
> Error 0x00000220/-1022
> Error during: Execution, OCS,
> PTI_ERR_ICE_WAIT_TO Error Occured at 0x00000000
>
> Sequence ID: 0
> Error Code: -1022
> Error Class: 0x00000220
> I/O Port = 240
>
> Board Name: C64xx Rev 1.0 TDS510USB Emulator - WintechDigital
> Cpu Name: CPU_1
>
> Abort: Close Code Composer Studio.
> Retry: Try to connect to the target again.
> Cancel: Remain disconnected from the target
> Diagnostic: Run diagnostic utility.
>
> please help me to solvethis problem
------- End of Original Message -------
J J-

1) Are you using a "full" (i.e. expensive) version of CCS? If not then you can't use the CCS version that came with
the DSK 6455 with the WinTech emulator.

2) You're connecting the WinTech emulator via 14-pin JTAG header on the DSK board, right? Normally the DSK is set to
use the USB port (PC connection). There should be a user switch you have to set to select the JTAG header and not USB
as the JTAG interface.

-Jeff

> ---------- Original Message -----------
> From: J J
> To: c...
> Sent: Tue, 20 Apr 2010 05:07:49 -0700 (PDT)
> Subject: [c6x] WINTECH TDS510PLUSE Jtag Emulator
>
>>
>>
>> Dear All
>> I want program digitalspectrum c6455 DSK with WINTECH TDS510PLUSE Jtag Emulator,
>> But when I connect board this error display
>>
>> Error connecting to the target:
>> Error 0x00000220/-1022
>> Error during: Execution, OCS,
>> PTI_ERR_ICE_WAIT_TO Error Occured at 0x00000000
>>
>> Sequence ID: 0
>> Error Code: -1022
>> Error Class: 0x00000220
>> I/O Port = 240
>>
>> Board Name: C64xx Rev 1.0 TDS510USB Emulator - WintechDigital
>> Cpu Name: CPU_1
>>
>> Abort: Close Code Composer Studio.
>> Retry: Try to connect to the target again.
>> Cancel: Remain disconnected from the target
>> Diagnostic: Run diagnostic utility.
>>
>> please help me to solvethis problem
> ------- End of Original Message -------

_____________________________________
JJ,

On Tue, Apr 20, 2010 at 6:25 PM, Jeff Brower wrote:

> J J-
>
> 1) Are you using a "full" (i.e. expensive) version of CCS? If not then you
> can't use the CCS version that came with
> the DSK 6455 with the WinTech emulator.
>
> 2) You're connecting the WinTech emulator via 14-pin JTAG header on the DSK
> board, right? Normally the DSK is set to
> use the USB port (PC connection). There should be a user switch you have to
> set to select the JTAG header and not USB
> as the JTAG interface.
>
> -Jeff
>

1. The error message is inconsistent with 'no target power '.
2. Jeff is correct that you need full CCS [#1].
3. All SD DSKs that I have seen have used the 'auto-JTAG switching
technique' that I first saw on the 6201 EVM designed by DNA Enterprises,
later used by TI on the 6211/6711 DSKs, and picked up by SD. [see schematics
for details]. There *should* not be a problem with JTAG connector selection.
4. The error message seems to indicate an emulation driver [or improper
configuration].
5. You should run xdsprobe to verify the JTAG scan chain integrity. If the
JTAG scan chain is good, you can focus on the emulation or CCS
configuration.
www.dsprelated.com/blogs-1/nf/Mike_Dunn.php
mikedunn

> > ---------- Original Message -----------
> > From: J J >
> > To: c...
> > Sent: Tue, 20 Apr 2010 05:07:49 -0700 (PDT)
> > Subject: [c6x] WINTECH TDS510PLUSE Jtag Emulator
> >
> >>
> >>
> >> Dear All
> >> I want program digitalspectrum c6455 DSK with WINTECH TDS510PLUSE Jtag
> Emulator,
> >> But when I connect board this error display
> >>
> >> Error connecting to the target:
> >> Error 0x00000220/-1022
> >> Error during: Execution, OCS,
> >> PTI_ERR_ICE_WAIT_TO Error Occured at 0x00000000
> >>
> >> Sequence ID: 0
> >> Error Code: -1022
> >> Error Class: 0x00000220
> >> I/O Port = 240
> >>
> >> Board Name: C64xx Rev 1.0 TDS510USB Emulator - WintechDigital
> >> Cpu Name: CPU_1
> >>
> >> Abort: Close Code Composer Studio.
> >> Retry: Try to connect to the target again.
> >> Cancel: Remain disconnected from the target
> >> Diagnostic: Run diagnostic utility.
> >>
> >> please help me to solvethis problem
> >>
> >>
> > ------- End of Original Message -------
> >
> >
>

--
www.dsprelated.com/blogs-1/nf/Mike_Dunn.php