Forums

RE: TI DM642

Started by manjunath January 14, 2004
Hi Calvin,
I would like to have some help from your side.
I am using USB JTAG for debugging the board having TI6415 processors.
But the JTAG is from company called Signum.
When i start the CCS 2.2 i am getting the following error.
"Error Code : 0x80000240/-180, This was generated by TI's USCIF Driver..
SC_ERR_CTL_NO_TRG_POWER"
Even though power is connected to board.

Anyone has encountered this problem and found solution for this.
please mail me.

Thanks and regards,
Manjunath

-----Original Message-----
From: twfoo8x8 [mailto:]
Sent: Wednesday, January 14, 2004 6:22 AM
To:
Subject: Re: TI DM642 Hi all,

Found the solution to this problem.

You must install the SDConfig program found on the TI DM642
installation disk. After that, everything is ok. After installation,
you should get a SDConfig 6000 icon on your desktop.

Installing the SDConfig program from the USB JTAG installation disk
is not enough. After installing this program, you'll get a SDConfig
x.xx icon on your desktop.

Best regards,
Calvin Foo
--- In , "manjunath" <gmanjunath@t...> wrote:
> Hi,
> To which port you have connected. and also which is the driver u
people are
> using?
> Since i am also using JTAG connected to USB for debugging .
> I think there could be wrong in driver being configured, but i am
not sure.
> i think u can look for this bug is in CCS2.2. check for bug list in
the TI
> site.
>
> hope it may help you people,
> Manjunath
>
> -----Original Message-----
> From: Jean-Michel MERCIER [mailto:jm.mercier@a...]
> Sent: Tuesday, January 13, 2004 3:24 PM
> To: twfoo8x8;
> Subject: RE: [c6x] TI DM642 >
> Hello,
>
> We have the same problem here.
>
> Did you found a workaround ?
>
> Jean-Michel. > > -----Message d'origine-----
> > De : twfoo8x8 [mailto:twfoo8x8@y...]
> > Envoy: vendredi 2 janvier 2004 08:32
> > :
> > Objet : [c6x] TI DM642
> >
> >
> > Hiya,
> >
> > I've purchased the above board and aUSB JTAG. However, I was not
able
> > to run the demo. Everything I load the .out file using CCS 2.20, I
> > get the message "does not match target type." What does this mean?
> >
> >
> > Thank you for your help.
> >
> > br,
> > twfoo
> >
> >
> >
> >
> >
> > _____________________________________
> > Note: If you do a simple "reply" with your email client, only the
> > author of this message will receive your answer. You need to do
> > a "reply all" if you want your answer to be distributed to the
> > entire group.
> >
> > _____________________________________
> > About this discussion group:
> >
> > To Join: Send an email to
> >
> > To Post: Send an email to
> >
> > To Leave: Send an email to
> >
> > Archives: http://www.yahoogroups.com/group/c6x
> >
> > Other Groups: http://www.dsprelated.com
> >
> >
> >
> >
> > _____________________________________
> Note: If you do a simple "reply" with your email client, only the
author of
> this message will receive your answer. You need to do a "reply
all" if you
> want your answer to be distributed to the entire group.
>
> _____________________________________
> About this discussion group:
>
> To Join: Send an email to
>
> To Post: Send an email to
>
> To Leave: Send an email to
>
> Archives: http://www.yahoogroups.com/group/c6x
>
> Other Groups: http://www.dsprelated.com >



Manjunath,
 
A couple of the most common causes of this error are:
1. Incorrect emulation driver selected in cc_setup
2. Incorrect configuration of the driver in cc_setup
 
Make sure that you use the correct driver for the Signum emulator.  There should be either a special driver that you select in cc_setup OR you should use the TI C64xx Rev 1.1 XDS510 Emulation driver with a special configuration file.
 
Check Signum's instructions or their web site
 
mikedunn

manjunath <g...@tataelxsi.co.in> wrote:
Hi Calvin,
I would like to have some help from your side.
I am using USB JTAG for debugging the board having TI6415 processors.
But the JTAG is from company called Signum.
When i start the CCS 2.2 i am getting the following error.
"Error Code : 0x80000240/-180, This was generated by TI's USCIF Driver..
SC_ERR_CTL_NO_TRG_POWER"
Even though power is connected to board.

Anyone has encountered this problem and found solution for this.
please mail me.

Thanks and regards,
Manjunath

-----Original Message-----
From: twfoo8x8 [mailto:t...@yahoo.com]
Sent: Wednesday, January 14, 2004 6:22 AM
To: g...@tataelxsi.co.in
Subject: Re: TI DM642Hi all,

Found the solution to this problem.

You must install the SDConfig program found on the TI DM642
installation disk. After that, everything is ok. After installation,
you should get a SDConfig 6000 icon on your desktop.

Installing the SDConfig program from the USB JTAG installation disk
is not enough. After installing this program, you'll get a SDConfig
x.xx icon on your desktop.

Best regards,
Calvin Foo
--- In c...@yahoogroups.com, "manjunath" wrote:
> Hi,
> To which port you have connected. and also which is the driver u
people are
> using?
> Since i am also using JTAG connected to USB for debugging .
> I think there could be wrong in driver being configured, but i am
not sure.
> i think u can look for this bug is in CCS2.2. check for bug list in
the TI
> site.
>
> hope it may help you people,
> Manjunath
>
> -----Original Message-----
> From: Jean-Michel MERCIER [mailto:jm.mercier@a...]
> Sent: Tuesday, January 13, 2004 3:24 PM
> To: twfoo8x8; c...@yahoogroups.com
> Subject: RE: [c6x] TI DM642>
> Hello,
>
> We have the same problem here.
>
> Did you found a workaround ?
>
> Jean-Michel.> > -----Message d'origine-----
> > De : twfoo8x8 [mailto:twfoo8x8@y...]
> > Envoy: vendredi 2 janvier 2004 08:32
> > : c...@yahoogroups.com
> > Objet : [c6x] TI DM642
> >
> >
> > Hiya,
> >
> > I've purchased the above board and aUSB JTAG. However, I was not
able
> > to run the demo. Everything I load the .out file using CCS 2.20, I
> > get the message "does not match target type." What does this mean?
> >
> >
> > Thank you for your help.
> >
> > br,
> > twfoo
> >
> >
> >
> >
> >
> > _____________________________________
> > Note: If you do a simple "reply" with your email client, only the
> > author of this message will receive your answer. You need to do
> > a "reply all" if you want your answer to be distributed to the
> > entire group.
> >
> > _____________________________________
> > About this discussion group:
> >
> > To Join: Send an email to c...@yahoogroups.com
> >
> > To Post: Send an email to c...@yahoogroups.com
> >
> > To Leave: Send an email to c...@yahoogroups.com
> >
> > Archives: http://www.yahoogroups.com/group/c6x
> >
> > Other Groups: http://www.dsprelated.com
> >
> >
> > Yahoo! Groups Links
> >
> > To visit your group on the web, go to:
> > http://groups.yahoo.com/group/c6x/
> >
> > To unsubscribe from this group, send an email to:
> > c...@yahoogroups.com
> >
> >
> >
> > _____________________________________
> Note: If you do a simple "reply" with your email client, only the
author of
> this message will receive your answer. You need to do a "reply
all" if you
> want your answer to be distributed to the entire group.
>
> _____________________________________
> About this discussion group:
>
> To Join: Send an email to c...@yahoogroups.com
>
> To Post: Send an email to c...@yahoogroups.com
>
> To Leave: Send an email to c...@yahoogroups.com
>
> Archives: http://www.yahoogroups.com/group/c6x
>
> Other Groups: http://www.dsprelated.com> Yahoo! Groups Links
>
> To visit your group on the web, go to:
> http://groups.yahoo.com/group/c6x/
>
> To unsubscribe from this group, send an email to:
> c...@yahoogroups.com_____________________________________
Note: If you do a simple "reply" with your email client, only the author of this message will receive your answer. You need to do a "reply all" if you want your answer to be distributed to the entire group.

_____________________________________
About this discussion group:

To Join: Send an email to c...@yahoogroups.com

To Post: Send an email to c...@yahoogroups.com

To Leave: Send an email to c...@yahoogroups.com

Archives: http://www.yahoogroups.com/group/c6x

Other Groups: http://www.dsprelated.comYahoo! Groups Links

To visit your group on the web, go to:
http://groups.yahoo.com/group/c6x/

To unsubscribe from this group, send an email to:
c...@yahoogroups.com