|
My pb is now solved. There are some (strange) times, where you should not use the latest releases... Here is one example. I tried to connect CCS to a C6711 dsp board in a third party product (Toro board/Innovative Integration). The emulator I used with is the xds510pp-plus. The lastest releases of the 510pp-plus jtag drivers seem not to be in a running state. Please find below some information about: The pb I had is that I wasn't able to connect the board after CCS launch. The message was: Error connecting to the target: Error 0x80000200/-180 Fatal Error during: OCS, This error was generated by TI's USCIF driver. SC_ERR_CTL_NO_TRG_POWER <-180> The controller has detected a target power loss. The user may have failed to turn-on or connect its source. Sequence ID: 0 Error Code: -180 Error Class: 0x80000200 I/O Port = 240 Board Name: C671x XDS510 Emulator Cpu Name: CPU_1 Abort: Close Code Composer Studio. Retry: Try to connect to the target again. Cancel: Remain disconnected from the target Diagnostic: Run diagnostic utility. As I expected, this was a driver pb! Instead of using the last release of Spectrum Digital emulator drivers, I used the drivers dedicated for the 2.2 version, and which are compatible with the 3.0 version: http://www.spectrumdigital.com/drivers/docstore/CodeComposerDrivers/C6000/Emulator/CodeComposerStudio-2.x/Release-2.21.00/ And everything goes OK. (at connect, I mean ;) ) (last remark: these drivers also have the connect/disconnect feature). Damien Couroussa rit : > > Hi everybody, > > Did anyone experienced connection problems with CCS 3.0? > > My board is a third party board from Innovative Integration (Toro), > including the C6711 dsp. > I use the xds510pp-plus JTAG. > > Actually, I can connect the emulator to the board with CCS v2.0, using > old drivers from Spectrum Digital. > > I downloaded from Spectrum Digital the most recent driver releases for > CCS 3.0 (setupCCSC6000_v30101.ZIP), but I can't connect to the board > with the 3.0 version. > Please find below a detailed description of the pb. > > Best regards, and thanks in advance for any answer. > > Damien, > > ---------------------------------- > > Development Tools Support > * Host Computer System: PC > * Operating System: Windows2000- SP 1&2(same pb with XP and SP 1 to 4) > * Product: C6711 / Toro board from Innovative Integration > > > Here is the message I get from CCS after launching: > -------- > > Error connecting to the target: > Error 0x80000200/-180 > Fatal Error during: OCS, > This error was generated by TI's USCIF driver. > > SC_ERR_CTL_NO_TRG_POWER <-180> > The controller has detected a target power loss. > The user may have failed to turn-on or connect its source. > > Sequence ID: 0 > Error Code: -180 > Error Class: 0x80000200 > I/O Port = 240 > > Board Name: C671x XDS510 Emulator > Cpu Name: CPU_1 > > Abort: Close Code Composer Studio. > Retry: Try to connect to the target again. > Cancel: Remain disconnected from the target > Diagnostic: Run diagnostic utility. > > ------- > > I checked everything with the SdConfig utility, and it seems OK: > > Parallel port in the BIOS setup is et to SP8 mode, using IRQ 7 & Base IO > address = 0x378. > > Power supply to the JTAG is OK, I checked 5.2 Volts. > > Messages I get from SdConfig are: > > ------- > > ** Checking for available printer ports > > $$ Printer port available at: > $$ EmuPortAddr=0x378 > $$ EmuPortMode=SPP8 > $$ EmuPortSpeed=0 > > ** Checking for available USB ports > ** Checking for a valid emulator/eZdsp > > $$ You are connected to: > $$ EmuProductName=XDS510PP_PLUS > $$ EmuPortAddr=0x378 > $$ EmuPortMode=SPP8 > $$ ProductId > $$ ProductVersion > > ** Checking for a valid emulator/eZdsp > > $$ You are connected to: > $$ EmuProductName=XDS510PP_PLUS > $$ EmuPortAddr=0x378 > $$ EmuPortMode=SPP8 > $$ ProductId > $$ ProductVersion > ** Checking emulator/eZdsp scan connection > > ** Emulator Test ** > > $$ EmuProductName=XDS510PP_PLUS > > $$ EmuPortAddr=0x378 > > $$ EmuPortMode=SPP8 > > $$ ProductId > > $$ ProductVersion > > ** Emulator Scan Test > > -- Found JTAG IR length of 46 > > -- Found 1 JTAG device(s) in the scan chain > > ** Emulator is reset > > ------ > > Last remark: I tried to configure the parallel port using different > modes (EPP, ECP), but the connection still fails. > > If I change the I/O port in the CCS setup, I get the following error > report, so I guess this is not that. > > ------ > Error connecting to the target: > Error 0x80000200/-118 > Fatal Error during: OCS, > This error was generated by TI's USCIF driver. > > SC_ERR_CTL_PORT <-118> > An invalid controller port value has been used. > Thus Unified-SCIF will not attempt to detect a controller > The standard 560 ports are 0x0, 0x1, 0x2 and 0x3. > The standard EVM ports are 0x0, 0x1, 0x2 and 0x3. > The standard DSK ports are 0x378, 0x278 and 0x3BC. > The standard 510 ports are 0x240, 0x280, 0x320 and 0x340. > Sequence ID: 0 > Error Code: -118 > Error Class: 0x80000200 > I/O Port = 378 > > Board Name: C62xx,C67xx XDS510 Emulator > Cpu Name: CPU_1 > > Abort: Close Code Composer Studio. > Retry: Try to connect to the target again. > Cancel: Remain disconnected from the target > Diagnostic: Run diagnostic utility. > ------ > -- Damien Courousse PhD Student Laboratoire ACROE-ICA INPG, 46 avenue Felix Viallet F-38031 Grenoble Cedex Tel: 33 4 76 57 46 70 Fax: 33 4 76 57 48 89 http://acroe.imag.fr -- Damien Courousse PhD Student Laboratoire ACROE-ICA INPG, 46 avenue Felix Viallet F-38031 Grenoble Cedex Tel: 33 4 76 57 46 70 Fax: 33 4 76 57 48 89 http://acroe.imag.fr |
[Fwd: Re: JTAG - CCS connection pbs]
Started by ●February 11, 2005
