Hello Everyone, I am developing an Audio application project on ADSP Bf537 EZ-LITE board. I have developed compression and...

Hello Everyone, I am developing an Audio application project on ADSP Bf537 EZ-LITE board. I have developed compression and decompression algorithms for the Audio samples. The algorithm is working fine and I have tested it. Now I want to achieve live recording and output the recorded samples at the speaker/headphone connected at "LINE_OUT" port of the board. I have a Mike f...

Hi! I want to Display an image on the Computer Monitor.... For that I have taken an image in MATLAB and Converted it into YCbCr format and...

Hi! I want to Display an image on the Computer Monitor.... For that I have taken an image in MATLAB and Converted it into YCbCr format and then Created a 1440*243 Buffer ( (525-40)/2 = 242.5 and i want to keep both fields same) for NTSC system... That Buffer I have included in a File and From that I have Created a 1716*525 Buffer With all Control Information...............................

Hi all We are working here to port u-boot on a BF561 based board while compiling u-boot-1.1.6-2008R1.5 with the latest toolchain iam getting...

Hi all We are working here to port u-boot on a BF561 based board while compiling u-boot-1.1.6-2008R1.5 with the latest toolchain iam getting the following error. Please help me to resolve the issue I have posted the error below bfin-uclinux-objcopy --gap-fill=0xff -O srec u-boot u-boot.srec bfin-uclinux-objcopy --gap-fill=0xff -O ihex u-boot u-boot.hex bfin-uclinux-objcopy --gap-fill=0xff...

Hello, I am working with Analog Devices Blackfin BF537 EZ Kit Lite board. I am storing the 16 bit audio samples of a PCM .wav file in the...

Hello, I am working with Analog Devices Blackfin BF537 EZ Kit Lite board. I am storing the 16 bit audio samples of a PCM .wav file in the memory. My implementation is as follows . 1) I store the Audio samples in the SDRAM memory by performing memory allocation. 2) Perform Adio reset in the beginning void Audio_Reset(void) { int i; // give some time for reset to ta...

Hi! I don't know whether i can post this question here or not...Anyway iam posting help me............ I have my Own BF-532 Board...

Hi! I don't know whether i can post this question here or not...Anyway iam posting help me............ I have my Own BF-532 Board with SDRAM(MT48LC8M8M16A2),Flash(M29W160Ecool smiley and Audio Codec(AD1836) I have a Small Problem with LD1117S12TR 1.2V Regulator ..... AS per the Bf533 Ezkit lite we have designed the Power Supply which is having a 3.3v regulator and 1.2V Regulator....3....

I am using SHARC 21160M to which PCI BRIDGE(PLX 9656)is connected , and to this PCI-VME BRIDGE(UNIVERSE 2 TUNDRA)is connected.I need to write a...

I am using SHARC 21160M to which PCI BRIDGE(PLX 9656)is connected , and to this PCI-VME BRIDGE(UNIVERSE 2 TUNDRA)is connected.I need to write a driver for this vme bus. Now I have accessed the registers for the PCI bridge(PLX 9656) till now. But I couldn't able to access the PCI-VME bridge(TUNDRA) registers through the PCI configuration space . Can any one please help me in configuring the PCI ...

Got to make a decision on what type of EPROM to use on the board. I was going to follow the EZLITE kit and use the AM29LV081B but that means it...

Got to make a decision on what type of EPROM to use on the board. I was going to follow the EZLITE kit and use the AM29LV081B but that means it must be either programmed before being soldered to the board, or I need a JTAG programmer. The latter is a possibility, but what of the conventional alternative of a socket and a big DIL package? Would there be any problems with the extra track lengt...

Since I need to access more than 4 devices on SPI I would like to use spare DAI pins as chip selects. Of the 4 flag pins I want to use the first...

Since I need to access more than 4 devices on SPI I would like to use spare DAI pins as chip selects. Of the 4 flag pins I want to use the first three as inputs for INTs from peripherals, and the fourth as an LED driver. Is there anything wrong with this setup? Specifically when I service an interrupt by using SPI? I've read the manual but still not entirely clear since a lot of emphasis is ...

I just ordered a ADSP-21369 kit. But because of the kit's weight, the shipping costed more than kit. I was told the kit's weight is over 13...

I just ordered a ADSP-21369 kit. But because of the kit's weight, the shipping costed more than kit. I was told the kit's weight is over 13 pound. I think this is too much weight for a development kit like this, I guess something is wrong. Please, can any of you tell me the aproximate weight of ADZS-21369-EZLITE kit? Thanks Jose --------------------------------- ?Busc?...

Hi all! I Have a Bf532 EVB. I want to Provide USB interface to BF532 For transferring data from system to Board ... I am Not Expert in USB...

Hi all! I Have a Bf532 EVB. I want to Provide USB interface to BF532 For transferring data from system to Board ... I am Not Expert in USB protocol...I just Know Details about USB protocol As BF532 is not having USB interface, I have got some choices to Provide USB connectivity to My board... USB to RS232 and USB to SPI chips i don't want to use Because they will not Provide less Speed...