*How are you !* *I have a embedded application based on BLackFIN processor and i wish to Know why i can downoald a free uclinux os and why i...

*How are you !* *I have a embedded application based on BLackFIN processor and i wish to Know why i can downoald a free uclinux os and why i will chose the Flash and SSRAM memory size in ordre to support uclinux os.* *please help me !* **

Hi, Anyone knows whether the blackfin 561 board can receive bluetooth signal? Is there any extension kit or board needed to connect to the...

Hi, Anyone knows whether the blackfin 561 board can receive bluetooth signal? Is there any extension kit or board needed to connect to the blackfin 561 board in order to receive the signal ?? If able to any examples will be great thanks. Regards,

Hi all, I am using m25p64 SPI Flash(ST) in my project. Shortly, I am connecting m25p64 with ADSP-BF532 DSP and I am booting the linux kernel...

Hi all, I am using m25p64 SPI Flash(ST) in my project. Shortly, I am connecting m25p64 with ADSP-BF532 DSP and I am booting the linux kernel from SPI Flash(m25p64), but sometimes I am facing a communication problem so I get Bad Data Crc message. I have searched and made many tests, finally I realised that the problem is about SCK pin of m25p64. I had put 100K resistor between SCK and GND like r...

In order to reduce the execution time of my program I need to use both processors. I just don't know how to do that? I'm using VisualDSP++. What...

In order to reduce the execution time of my program I need to use both processors. I just don't know how to do that? I'm using VisualDSP++. What are the instructions, how much is to be gained by that. The program is multiplying matrices, and I figured one processor to multiply one part, and the other some other part, and then to exchange results.

Hello people. I'm using BlackFin BF533 EZ-Kit with ISP1761 as a USB Host Controller. I could succesfully enumerate the internal root hub...

Hello people. I'm using BlackFin BF533 EZ-Kit with ISP1761 as a USB Host Controller. I could succesfully enumerate the internal root hub thanks to the documentation from NXP: AN10037, AN10054. (BTW, also found out some corrections to AN10037, such as writing HC Status Buffer Register) Well, I can send and receive tokens to the root hub, set its address and power the ports using the SetFe...

Hi, I am using first time BF-DSP processors.I need some clarification regarding sample code of JEG-decoder. 1) I am using sample...

Hi, I am using first time BF-DSP processors.I need some clarification regarding sample code of JEG-decoder. 1) I am using sample JEG Decoder, which is provided by ADI(arith_decoder_JPEG2000). 2) It contains one .c file &two.asm files. 3) my doubt--> how the output is dumping.i.e in the formatt of RGB or YUV if it is RGB, is it dumping RGB,RGB,...etc or RRRRR...

Hello I need to implement UART on ADSP21363. I find EE note on Analog web site for previous Sharc, solution is based on SPORT. Does anyone...

Hello I need to implement UART on ADSP21363. I find EE note on Analog web site for previous Sharc, solution is based on SPORT. Does anyone have experience on 2136x. I also find MAX3100 chip (UART on SPI), Does anyone have experience with this chip ? Thanks in advance

Hi! I just want a programming help... In the Assembly language there is command CALL (P0); It will run the code at P0 (0xffa08000)...

Hi! I just want a programming help... In the Assembly language there is command CALL (P0); It will run the code at P0 (0xffa08000) ..... How can i implement same thing in c language... thank u.......

Hello, Does any of you know of Blackfin based boards, different from ADI (EzKits) = Bluetechnix, Zbrain, Avnet VSK or Surveyor, which is low...

Hello, Does any of you know of Blackfin based boards, different from ADI (EzKits) = Bluetechnix, Zbrain, Avnet VSK or Surveyor, which is low cost and has: - SDRAM - Flash - Analog Video Input - Some GPIO - UART Regards. =20 Jaime Andr=E9s Aranguren Cardona j...@ieee.org j...@computer.org _____________________________________________________________________= ______________...

Hello, We had a similar problem, and a colleague of mine found out that there is a statement to be put in comments (in short, removed) if you...

Hello, We had a similar problem, and a colleague of mine found out that there is a statement to be put in comments (in short, removed) if you are using a higher version of the BF535 chip in your ez-kit. Check lines 103-104 in the Init_Interrupts function: // for chip revisions > = 1.0 remove the following instruction (needed for anomaly "IMASK bit polarity") *pSIC_IMASK = 0xffffffcf; So, si