I've been learning how to program on the 56800/E at this link http://www.techonline.com/comm unity/ed_resource/virtualab. This company lets...

I've been learning how to program on the 56800/E at this link http://www.techonline.com/comm unity/ed_resource/virtualab. This company lets you use real eval boards for free. The eval boards are accessible online, they are not emulators or simulators. Has anyone else checked this out?

I need to debug my application with a notebook that don't have a parallel interface; for this reason I get a PCMCIA card that allow the ...

I need to debug my application with a notebook that don't have a parallel interface; for this reason I get a PCMCIA card that allow the link between PC and J-TAG interface. The drivers is "OX12PCI840 PCI Paralll Port" and it is correctly installed because with others application it run. The problem is that the metrowerks debugger don't run.

Has anyone used these new small parts yet. They seem to be on silly 17 week lead times and I would like to know how they expect up to design...

Has anyone used these new small parts yet. They seem to be on silly 17 week lead times and I would like to know how they expect up to design them in when they are so hard to get. Also they have totally different pinout even thougth both come in 80 pin tqfp. Which would be the safest one to use as you cannot easly change your mind. On a more techical side has

Low-end digital signal controller helps reduce production costs and speed time to market TEMPE, Ariz. ? May 2, 2005 ? As energy costs...

Low-end digital signal controller helps reduce production costs and speed time to market TEMPE, Ariz. ? May 2, 2005 ? As energy costs soar, designers of industrial and appliance applications are looking for economical ways to offer more functionality and energy efficiency in their products. Freescale Semiconductor (NYSE:FSL, FSL.B) has responded

> >I used to program the 56F80X family of DSPs with Codewarrior 5.0. Now, I am >implementing HC908s as a low cost replacement in low-end...

> >I used to program the 56F80X family of DSPs with Codewarrior 5.0. Now, I am >implementing HC908s as a low cost replacement in low-end applications. > >Questions: >1) Does anybody know any other Motorola/Yahoo group as good as this one? I >searched but got nothing. >2) Regarding Codewarrior environment, is it the same

-----Original Message----- From: processor_expert [mailto:processor_expert@proc...] Sent: Tuesday, May 03, 2005 6:11 AM To:...

-----Original Message----- From: processor_expert [mailto:processor_expert@proc...] Sent: Tuesday, May 03, 2005 6:11 AM To: motoroladsp-owner@moto... Subject: Re: Using address pin as GPIO on 56F805 with PE Currently, there is not possible to use only a part of the address bus in the CPU bean options. We are planing such option

Hello,             I’ve already done this when I was using the SDK but I can’t figure how to do it with...

Hello,             I’ve already done this when I was using the SDK but I can’t figure how to do it with Processor Expert. What I want to do is: while still

Hi everyone, Can any one suggest papers or refrence design on DSP cores with multiple mac and vliw instruction set support? Regards ...

Hi everyone, Can any one suggest papers or refrence design on DSP cores with multiple mac and vliw instruction set support? Regards Siddharth

if we have a gp?o configured to work with rissing and falling edge, we need to now wich edge active the interruption

if we have a gp?o configured to work with rissing and falling edge, we need to now wich edge active the interruption

AFAIK the only way ist to check it in the interrupt routine with reading the GPIO data register. Georg Bende > -----Urspr?ngliche...

AFAIK the only way ist to check it in the interrupt routine with reading the GPIO data register. Georg Bende > -----Urspr?ngliche Nachricht----- > Von: motoroladsp@moto... > [mailto:motoroladsp@moto...] Im Auftrag von rficoca2 > Gesendet: Montag, 25. April 2005 22:24 > An: motoroladsp@moto... > Betreff: [motoroladsp] h