Hi all,
>
>I have a XDS510-USB2.0 TI DSP Emulator like the iten number 270438990974 on
www.ebay.com and a custom board with dsp C6726. The problem is that the emulator
can't connect my target board.
>
>I am currently using Windows XP SP3. The system I have installed is CCS3.3.38.2
and I have used CCS Setup to add "C672x XDS510 Emulator" to my system
configuration. This configuration provides a BYPASS_0 processor type and a
TMS320C6720_0 processor type with driver "tixds6000.drv". I have changed
Property/Configuration File
>with "XDS510-USB2.cfg" provided with the Emulator, saved and quit.
>
>Then while starting the CCS3.3 it is showing the error below:
>
>Error connecting to the target:
>Error 0x80000200/-180
>Fatal Error during: OCS,
>This error was generated by TI's USCIF driver.
>
>SC_ERR_CTL_NO_TRG_POWER
>The controller has detected a target power loss.
>The user may have failed to turn-on or connect its source.
>Sequence ID: 0
>Error Code: -180
>Error Class: 0x80000200
>I/O Port = 0
>
>Board Name: C672x XDS510 Emulator
>Cpu Name: TMS320C6720_0
>
>Abort: Close Code Composer Studio.
>Retry: Try to connect to the target again.
>Cancel: Remain disconnected from the target
>Diagnostic: Run diagnostic utility.
>
>Looking the error, the I/O port = 0 is diferent from the I/O port I configured
in the CCS Setup (I/O port = 0x240). My gess is that the
>problem is something related to the drivers.
>
>I have tried with different CCS configurations but nothing changes.
>
>Referring to the hardware, I inserted a probe to check all JTAG signals between
my target board and the emulator and found that the TMS, TSR, TDI, TDO, PD,
/TRST, EMU0 amd EMU1 are at 3.3V. Also the pins TCK and TCK_RET are with signal
clock. To me seems that the board is fine.
>
>Anyone who develop applications on the C672x and use this emulator had the same
problem?
>Does somebody know what I have to do in order to solve problem?
>
>Please give me a light.
>
>Thanks in advance
>
>Tatiano Busatto
>
>_____________________________________
>
>Hi Tatiano,
I have the same problem withxds 510-usb2.0 Ti Dsp emulator that is a
Chinese made.
Whould you please help me if your problem was solved.
Thanks,
Mazaheri.
_____________________________________
Re: XDS510-USB2.0 + C6726 - Problem to connect...
Started by ●November 3, 2010
Reply by ●November 3, 20102010-11-03
z1384,
A few things to check...
--have you downloaded and installed the .dll file from TI or spectrum digital
for the specific DSP/emulator/USB connection?
R. Williams
---------- Original Message -----------
From: z...@yahoo.com
To: c...
Sent: Wed, 03 Nov 2010 09:35:07 -0400
Subject: [c6x] Re: XDS510-USB2.0 + C6726 - Problem to connect...
> Hi all,
> >
> >I have a XDS510-USB2.0 TI DSP Emulator like the iten number 270438990974 on
www.ebay.com and a custom board with dsp C6726. The problem is that the
emulator can't connect my target board.
> >
> >I am currently using Windows XP SP3. The system I have installed is
CCS3.3.38.2 and I have used CCS Setup to add "C672x XDS510 Emulator" to my
system configuration. This configuration provides a BYPASS_0 processor type
and a TMS320C6720_0 processor type with driver "tixds6000.drv". I have changed
Property/Configuration File
> >with "XDS510-USB2.cfg" provided with the Emulator, saved and quit.
> >
> >Then while starting the CCS3.3 it is showing the error below:
> >
> >Error connecting to the target:
> >Error 0x80000200/-180
> >Fatal Error during: OCS,
> >This error was generated by TI's USCIF driver.
> >
> >SC_ERR_CTL_NO_TRG_POWER
> >The controller has detected a target power loss.
> >The user may have failed to turn-on or connect its source.
> >Sequence ID: 0
> >Error Code: -180
> >Error Class: 0x80000200
> >I/O Port = 0
> >
> >Board Name: C672x XDS510 Emulator
> >Cpu Name: TMS320C6720_0
> >
> >Abort: Close Code Composer Studio.
> >Retry: Try to connect to the target again.
> >Cancel: Remain disconnected from the target
> >Diagnostic: Run diagnostic utility.
> >
> >Looking the error, the I/O port = 0 is diferent from the I/O port I
configured in the CCS Setup (I/O port = 0x240). My gess is that the
> >problem is something related to the drivers.
> >
> >I have tried with different CCS configurations but nothing changes.
> >
> >Referring to the hardware, I inserted a probe to check all JTAG signals
between my target board and the emulator and found that the TMS, TSR, TDI,
TDO, PD, /TRST, EMU0 amd EMU1 are at 3.3V. Also the pins TCK and TCK_RET are
with signal clock. To me seems that the board is fine.
> >
> >Anyone who develop applications on the C672x and use this emulator had the
same problem?
> >Does somebody know what I have to do in order to solve problem?
> >
> >Please give me a light.
> >
> >Thanks in advance
> >
> >Tatiano Busatto
> >
> >_____________________________________
> >
> >Hi Tatiano,
> I have the same problem withxds 510-usb2.0 Ti Dsp emulator that is a
> Chinese made. Whould you please help me if your problem was solved.
> Thanks, Mazaheri.
------- End of Original Message -------
_____________________________________
A few things to check...
--have you downloaded and installed the .dll file from TI or spectrum digital
for the specific DSP/emulator/USB connection?
R. Williams
---------- Original Message -----------
From: z...@yahoo.com
To: c...
Sent: Wed, 03 Nov 2010 09:35:07 -0400
Subject: [c6x] Re: XDS510-USB2.0 + C6726 - Problem to connect...
> Hi all,
> >
> >I have a XDS510-USB2.0 TI DSP Emulator like the iten number 270438990974 on
www.ebay.com and a custom board with dsp C6726. The problem is that the
emulator can't connect my target board.
> >
> >I am currently using Windows XP SP3. The system I have installed is
CCS3.3.38.2 and I have used CCS Setup to add "C672x XDS510 Emulator" to my
system configuration. This configuration provides a BYPASS_0 processor type
and a TMS320C6720_0 processor type with driver "tixds6000.drv". I have changed
Property/Configuration File
> >with "XDS510-USB2.cfg" provided with the Emulator, saved and quit.
> >
> >Then while starting the CCS3.3 it is showing the error below:
> >
> >Error connecting to the target:
> >Error 0x80000200/-180
> >Fatal Error during: OCS,
> >This error was generated by TI's USCIF driver.
> >
> >SC_ERR_CTL_NO_TRG_POWER
> >The controller has detected a target power loss.
> >The user may have failed to turn-on or connect its source.
> >Sequence ID: 0
> >Error Code: -180
> >Error Class: 0x80000200
> >I/O Port = 0
> >
> >Board Name: C672x XDS510 Emulator
> >Cpu Name: TMS320C6720_0
> >
> >Abort: Close Code Composer Studio.
> >Retry: Try to connect to the target again.
> >Cancel: Remain disconnected from the target
> >Diagnostic: Run diagnostic utility.
> >
> >Looking the error, the I/O port = 0 is diferent from the I/O port I
configured in the CCS Setup (I/O port = 0x240). My gess is that the
> >problem is something related to the drivers.
> >
> >I have tried with different CCS configurations but nothing changes.
> >
> >Referring to the hardware, I inserted a probe to check all JTAG signals
between my target board and the emulator and found that the TMS, TSR, TDI,
TDO, PD, /TRST, EMU0 amd EMU1 are at 3.3V. Also the pins TCK and TCK_RET are
with signal clock. To me seems that the board is fine.
> >
> >Anyone who develop applications on the C672x and use this emulator had the
same problem?
> >Does somebody know what I have to do in order to solve problem?
> >
> >Please give me a light.
> >
> >Thanks in advance
> >
> >Tatiano Busatto
> >
> >_____________________________________
> >
> >Hi Tatiano,
> I have the same problem withxds 510-usb2.0 Ti Dsp emulator that is a
> Chinese made. Whould you please help me if your problem was solved.
> Thanks, Mazaheri.
------- End of Original Message -------
_____________________________________
Reply by ●November 3, 20102010-11-03
Tatiano,
On 11/3/2010 8:35 AM, z...@yahoo.com wrote:
>
> Hi all,
> >
> >I have a XDS510-USB2.0 TI DSP Emulator like the iten number
> 270438990974 on www.ebay.com and a custom board with dsp C6726. The
> problem is that the emulator can't connect my target board.
>
Just to be clear, the emulators that I have seen on eBay are more
correctly described as "chinese manufactured emulators with counterfeit
TI markings that support most TI DSPs". These have showed up under
various names and usually do not include any support. They have a
history of not working with c672x devices.
Now that I have got you "cheered up"...
1. there are several discussions in the archives on this subject
2. you can check
www.dsprelated.com/blogs-1/nf/Mike_Dunn.php
mikedunn
> >
> >I am currently using Windows XP SP3. The system I have installed is
> CCS3.3.38.2 and I have used CCS Setup to add "C672x XDS510 Emulator"
> to my system configuration. This configuration provides a BYPASS_0
> processor type and a TMS320C6720_0 processor type with driver
> "tixds6000.drv". I have changed Property/Configuration File
> >with "XDS510-USB2.cfg" provided with the Emulator, saved and quit.
> >
> >Then while starting the CCS3.3 it is showing the error below:
> >
> >Error connecting to the target:
> >Error 0x80000200/-180
> >Fatal Error during: OCS,
> >This error was generated by TI's USCIF driver.
> >
> >SC_ERR_CTL_NO_TRG_POWER
> >The controller has detected a target power loss.
> >The user may have failed to turn-on or connect its source.
> >Sequence ID: 0
> >Error Code: -180
> >Error Class: 0x80000200
> >I/O Port = 0
> >
> >Board Name: C672x XDS510 Emulator
> >Cpu Name: TMS320C6720_0
> >
> >Abort: Close Code Composer Studio.
> >Retry: Try to connect to the target again.
> >Cancel: Remain disconnected from the target
> >Diagnostic: Run diagnostic utility.
> >
> >Looking the error, the I/O port = 0 is diferent from the I/O port I
> configured in the CCS Setup (I/O port = 0x240). My gess is that the
> >problem is something related to the drivers.
> >
> >I have tried with different CCS configurations but nothing changes.
> >
> >Referring to the hardware, I inserted a probe to check all JTAG
> signals between my target board and the emulator and found that the
> TMS, TSR, TDI, TDO, PD, /TRST, EMU0 amd EMU1 are at 3.3V. Also the
> pins TCK and TCK_RET are with signal clock. To me seems that the board
> is fine.
> >
> >Anyone who develop applications on the C672x and use this emulator
> had the same problem?
> >Does somebody know what I have to do in order to solve problem?
> >
> >Please give me a light.
> >
> >Thanks in advance
> >
> >Tatiano Busatto
> >
> >_____________________________________
> >
> >Hi Tatiano,
> I have the same problem withxds 510-usb2.0 Ti Dsp emulator that is a
> Chinese made.
> Whould you please help me if your problem was solved.
> Thanks,
> Mazaheri.
On 11/3/2010 8:35 AM, z...@yahoo.com wrote:
>
> Hi all,
> >
> >I have a XDS510-USB2.0 TI DSP Emulator like the iten number
> 270438990974 on www.ebay.com and a custom board with dsp C6726. The
> problem is that the emulator can't connect my target board.
>
Just to be clear, the emulators that I have seen on eBay are more
correctly described as "chinese manufactured emulators with counterfeit
TI markings that support most TI DSPs". These have showed up under
various names and usually do not include any support. They have a
history of not working with c672x devices.
Now that I have got you "cheered up"...
1. there are several discussions in the archives on this subject
2. you can check
www.dsprelated.com/blogs-1/nf/Mike_Dunn.php
mikedunn
> >
> >I am currently using Windows XP SP3. The system I have installed is
> CCS3.3.38.2 and I have used CCS Setup to add "C672x XDS510 Emulator"
> to my system configuration. This configuration provides a BYPASS_0
> processor type and a TMS320C6720_0 processor type with driver
> "tixds6000.drv". I have changed Property/Configuration File
> >with "XDS510-USB2.cfg" provided with the Emulator, saved and quit.
> >
> >Then while starting the CCS3.3 it is showing the error below:
> >
> >Error connecting to the target:
> >Error 0x80000200/-180
> >Fatal Error during: OCS,
> >This error was generated by TI's USCIF driver.
> >
> >SC_ERR_CTL_NO_TRG_POWER
> >The controller has detected a target power loss.
> >The user may have failed to turn-on or connect its source.
> >Sequence ID: 0
> >Error Code: -180
> >Error Class: 0x80000200
> >I/O Port = 0
> >
> >Board Name: C672x XDS510 Emulator
> >Cpu Name: TMS320C6720_0
> >
> >Abort: Close Code Composer Studio.
> >Retry: Try to connect to the target again.
> >Cancel: Remain disconnected from the target
> >Diagnostic: Run diagnostic utility.
> >
> >Looking the error, the I/O port = 0 is diferent from the I/O port I
> configured in the CCS Setup (I/O port = 0x240). My gess is that the
> >problem is something related to the drivers.
> >
> >I have tried with different CCS configurations but nothing changes.
> >
> >Referring to the hardware, I inserted a probe to check all JTAG
> signals between my target board and the emulator and found that the
> TMS, TSR, TDI, TDO, PD, /TRST, EMU0 amd EMU1 are at 3.3V. Also the
> pins TCK and TCK_RET are with signal clock. To me seems that the board
> is fine.
> >
> >Anyone who develop applications on the C672x and use this emulator
> had the same problem?
> >Does somebody know what I have to do in order to solve problem?
> >
> >Please give me a light.
> >
> >Thanks in advance
> >
> >Tatiano Busatto
> >
> >_____________________________________
> >
> >Hi Tatiano,
> I have the same problem withxds 510-usb2.0 Ti Dsp emulator that is a
> Chinese made.
> Whould you please help me if your problem was solved.
> Thanks,
> Mazaheri.
Reply by ●November 3, 20102010-11-03
Mike,
In all my years of working with the CCS product, I had not previously heard of
this utility nor of the 'fake' CCS products.
Thanks for the info,
This will be a big help the next time I'm having a problem and will give me
one more hardware setup debug tool I can use.
R. Williams
---------- Original Message -----------
From: mikedunn
To: z...@yahoo.com
Cc: c...
Sent: Wed, 03 Nov 2010 11:38:08 -0500
Subject: Re: [c6x] Re: XDS510-USB2.0 + C6726 - Problem to connect...
>
> Just to be clear, the emulators that I have seen on eBay are more
> correctly described as "chinese manufactured emulators with
> counterfeit TI markings that support most TI DSPs". These have showed
> up under various names and usually do not include any support. They
> have a history of not working with c672x devices. Now that I have got
> you "cheered up"...
> 1. there are several discussions in the archives on this subject
> 2. you can check
>
> www.dsprelated.com/blogs-1/nf/Mike_Dunn.php
>
> mikedunn
_____________________________________
In all my years of working with the CCS product, I had not previously heard of
this utility nor of the 'fake' CCS products.
Thanks for the info,
This will be a big help the next time I'm having a problem and will give me
one more hardware setup debug tool I can use.
R. Williams
---------- Original Message -----------
From: mikedunn
To: z...@yahoo.com
Cc: c...
Sent: Wed, 03 Nov 2010 11:38:08 -0500
Subject: Re: [c6x] Re: XDS510-USB2.0 + C6726 - Problem to connect...
>
> Just to be clear, the emulators that I have seen on eBay are more
> correctly described as "chinese manufactured emulators with
> counterfeit TI markings that support most TI DSPs". These have showed
> up under various names and usually do not include any support. They
> have a history of not working with c672x devices. Now that I have got
> you "cheered up"...
> 1. there are several discussions in the archives on this subject
> 2. you can check
>
> www.dsprelated.com/blogs-1/nf/Mike_Dunn.php
>
> mikedunn
_____________________________________
Reply by ●November 4, 20102010-11-04
I have an emulator bought from ebay that, apart from some minor visual
differences (it says "made in china" instead of "texas instruments"), I believe
is exactly the same product (market as "XDS510-USB2.0"). After facing some
difficulties to connect my target (an C6424 board) to CCS 3.3, in the same way
that you did, I turned out to discover that internally my emulator was a copy of
a "Blackhawk USB 2.0 JTAG Emulator".
So, I uninstalled the previous "XDS510-wanna-be" driver from device manager (in windows safe mode), and installed the contents of the folder "D:\XDS510 USB2.0 DSP\BlackHawk Special Driver For CCS3.3" from the CD (you might have the same path on your disk). Next time when I plugged in the emulator to the USB port, I pointed windows to install the driver from "D:\XDS510 USB2.0 DSP\USB_driver" (windows asked for the driver twice, if I remember well...). Then, finally, I had a BlackHawk emulator displayed in device manager.
Later, I went to CCS Setup and by trial and error found that the target "Blackhawk USB 2.0 - C6455 Emulator with ICEPICK_C" worked flawlessly with my C6424 board. I even used Flashburn with it with no problem.
Hope this helps,
Vitor
--- On Wed, 11/3/10, z...@yahoo.com wrote:
From: z...@yahoo.com
Subject: [c6x] Re: XDS510-USB2.0 + C6726 - Problem to connect...
To: c...
Date: Wednesday, November 3, 2010, 11:35 AM
Hi all,
>
>I have a XDS510-USB2.0 TI DSP Emulator like the iten number 270438990974 on www.ebay.com and a custom board with dsp C6726. The problem is that the emulator can't connect my target board.
>
>I am currently using Windows XP SP3. The system I have installed is CCS3.3.38.2 and I have used CCS Setup to add "C672x XDS510 Emulator" to my system configuration. This configuration provides a BYPASS_0 processor type and a TMS320C6720_0 processor type with driver "tixds6000.drv". I have changed Property/Configuration File
>with "XDS510-USB2.cfg" provided with the Emulator, saved and quit.
>
>Then while starting the CCS3.3 it is showing the error below:
>
>Error connecting to the target:
>Error 0x80000200/-180
>Fatal Error during: OCS,
>This error was generated by TI's USCIF driver.
>
>SC_ERR_CTL_NO_TRG_POWER
>The controller has detected a target power loss.
>The user may have failed to turn-on or connect its source.
>Sequence ID: 0
>Error Code: -180
>Error Class: 0x80000200
>I/O Port = 0
>
>Board Name: C672x XDS510 Emulator
>Cpu Name: TMS320C6720_0
>
>Abort: Close Code Composer Studio.
>Retry: Try to connect to the target again.
>Cancel: Remain disconnected from the target
>Diagnostic: Run diagnostic utility.
>
>Looking the error, the I/O port = 0 is diferent from the I/O port I configured in the CCS Setup (I/O port = 0x240). My gess is that the
>problem is something related to the drivers.
>
>I have tried with different CCS configurations but nothing changes.
>
>Referring to the hardware, I inserted a probe to check all JTAG signals between my target board and the emulator and found that the TMS, TSR, TDI, TDO, PD, /TRST, EMU0 amd EMU1 are at 3.3V. Also the pins TCK and TCK_RET are with signal clock. To me seems that the board is fine.
>
>Anyone who develop applications on the C672x and use this emulator had the same problem?
>Does somebody know what I have to do in order to solve problem?
>
>Please give me a light.
>
>Thanks in advance
>
>Tatiano Busatto
>
>_____________________________________
>
>Hi Tatiano,
I have the same problem withxds 510-usb2.0 Ti Dsp emulator that is a Chinese made.
Whould you please help me if your problem was solved.
Thanks,
Mazaheri.
So, I uninstalled the previous "XDS510-wanna-be" driver from device manager (in windows safe mode), and installed the contents of the folder "D:\XDS510 USB2.0 DSP\BlackHawk Special Driver For CCS3.3" from the CD (you might have the same path on your disk). Next time when I plugged in the emulator to the USB port, I pointed windows to install the driver from "D:\XDS510 USB2.0 DSP\USB_driver" (windows asked for the driver twice, if I remember well...). Then, finally, I had a BlackHawk emulator displayed in device manager.
Later, I went to CCS Setup and by trial and error found that the target "Blackhawk USB 2.0 - C6455 Emulator with ICEPICK_C" worked flawlessly with my C6424 board. I even used Flashburn with it with no problem.
Hope this helps,
Vitor
--- On Wed, 11/3/10, z...@yahoo.com wrote:
From: z...@yahoo.com
Subject: [c6x] Re: XDS510-USB2.0 + C6726 - Problem to connect...
To: c...
Date: Wednesday, November 3, 2010, 11:35 AM
Hi all,
>
>I have a XDS510-USB2.0 TI DSP Emulator like the iten number 270438990974 on www.ebay.com and a custom board with dsp C6726. The problem is that the emulator can't connect my target board.
>
>I am currently using Windows XP SP3. The system I have installed is CCS3.3.38.2 and I have used CCS Setup to add "C672x XDS510 Emulator" to my system configuration. This configuration provides a BYPASS_0 processor type and a TMS320C6720_0 processor type with driver "tixds6000.drv". I have changed Property/Configuration File
>with "XDS510-USB2.cfg" provided with the Emulator, saved and quit.
>
>Then while starting the CCS3.3 it is showing the error below:
>
>Error connecting to the target:
>Error 0x80000200/-180
>Fatal Error during: OCS,
>This error was generated by TI's USCIF driver.
>
>SC_ERR_CTL_NO_TRG_POWER
>The controller has detected a target power loss.
>The user may have failed to turn-on or connect its source.
>Sequence ID: 0
>Error Code: -180
>Error Class: 0x80000200
>I/O Port = 0
>
>Board Name: C672x XDS510 Emulator
>Cpu Name: TMS320C6720_0
>
>Abort: Close Code Composer Studio.
>Retry: Try to connect to the target again.
>Cancel: Remain disconnected from the target
>Diagnostic: Run diagnostic utility.
>
>Looking the error, the I/O port = 0 is diferent from the I/O port I configured in the CCS Setup (I/O port = 0x240). My gess is that the
>problem is something related to the drivers.
>
>I have tried with different CCS configurations but nothing changes.
>
>Referring to the hardware, I inserted a probe to check all JTAG signals between my target board and the emulator and found that the TMS, TSR, TDI, TDO, PD, /TRST, EMU0 amd EMU1 are at 3.3V. Also the pins TCK and TCK_RET are with signal clock. To me seems that the board is fine.
>
>Anyone who develop applications on the C672x and use this emulator had the same problem?
>Does somebody know what I have to do in order to solve problem?
>
>Please give me a light.
>
>Thanks in advance
>
>Tatiano Busatto
>
>_____________________________________
>
>Hi Tatiano,
I have the same problem withxds 510-usb2.0 Ti Dsp emulator that is a Chinese made.
Whould you please help me if your problem was solved.
Thanks,
Mazaheri.
