Hi all,
I have a XDS510-USB2.0 TI DSP Emulator as
"http://www.lt430.com/ProductShow.asp?ID9" and a custom board with dsp C6727. I
have installed CCS3.3.54.1 and I have used CCS Setup to add "C672x XDS510
Emulator" to my system configuration. This configuration provides a BYPASS_0
processor type and a TMS320C6720_0 processor type with driver "tixds6000.drv". I
have changed Property/Configuration File with "XDS510-USB2.cfg" provided with
the Emulator, saved and quit.
I start CCS3, I can reset, I can connect to the board, I can see the memory and
registers correctly, but when I "Load Program", loading is executed without
errors, all symbols are loaded but memory is unchanged.
If I try to write a memory address directly or if I load a dat file, it works, I
can see the memory to change value, but if I load my program, memory is not
overwritten by the code of the program.
Please, help me
_____________________________________
XDS510-USB2.0 + C6727 - Load Program problem
Started by ●June 25, 2009
Reply by ●June 25, 20092009-06-25
pco73,
I have not seen this device.
According to TI, this is NOT a TI product. [nor does it look like it
is 'legit TI']
It appears to be a forgery of someone's emulator stuffed in an 'off
the shelf box' with TI markings.
mikedunn
On Thu, Jun 25, 2009 at 3:26 PM, wrote:
> Hi all,
>
> I have a XDS510-USB2.0 TI DSP Emulator as
> "http://www.lt430.com/ProductShow.asp?ID9" and a custom board with dsp
> C6727. I have installed CCS3.3.54.1 and I have used CCS Setup to add "C672x
> XDS510 Emulator" to my system configuration. This configuration provides a
> BYPASS_0 processor type and a TMS320C6720_0 processor type with driver
> "tixds6000.drv". I have changed Property/Configuration File with
> "XDS510-USB2.cfg" provided with the Emulator, saved and quit.
>
> I start CCS3, I can reset, I can connect to the board, I can see the memory
> and registers correctly, but when I "Load Program", loading is executed
> without errors, all symbols are loaded but memory is unchanged.
>
> If I try to write a memory address directly or if I load a dat file, it
> works, I can see the memory to change value, but if I load my program,
> memory is not overwritten by the code of the program.
>
> Please, help me
--
www.dsprelated.com/blogs-1/nf/Mike_Dunn.php
_____________________________________
I have not seen this device.
According to TI, this is NOT a TI product. [nor does it look like it
is 'legit TI']
It appears to be a forgery of someone's emulator stuffed in an 'off
the shelf box' with TI markings.
mikedunn
On Thu, Jun 25, 2009 at 3:26 PM, wrote:
> Hi all,
>
> I have a XDS510-USB2.0 TI DSP Emulator as
> "http://www.lt430.com/ProductShow.asp?ID9" and a custom board with dsp
> C6727. I have installed CCS3.3.54.1 and I have used CCS Setup to add "C672x
> XDS510 Emulator" to my system configuration. This configuration provides a
> BYPASS_0 processor type and a TMS320C6720_0 processor type with driver
> "tixds6000.drv". I have changed Property/Configuration File with
> "XDS510-USB2.cfg" provided with the Emulator, saved and quit.
>
> I start CCS3, I can reset, I can connect to the board, I can see the memory
> and registers correctly, but when I "Load Program", loading is executed
> without errors, all symbols are loaded but memory is unchanged.
>
> If I try to write a memory address directly or if I load a dat file, it
> works, I can see the memory to change value, but if I load my program,
> memory is not overwritten by the code of the program.
>
> Please, help me
--
www.dsprelated.com/blogs-1/nf/Mike_Dunn.php
_____________________________________
