Hello,
I've problem connecting the target via CCS 3.3 .
I use JTAG adapter to connect to target in which I set the switches to
default state(ie. All OFF state)
It give the following error:
Error connecting to the target:
Error 0x80000240/-180
Fatal Error during: Initialization, OCS,
This error was generated by TI's USCIF driver.
SC_ERR_CTL_NO_TRG_POWER <-180>
The controller has detected a target power loss.
The user may have failed to turn-on or connect its source.
Sequence ID: 0
Error Code: -180
Error Class: 0x80000240
I/O Port = 0
Board Name: DM6446 XDS510 Emulator
Cpu Name: ICEPICK_C_0
Abort: Close Code Composer Studio.
Retry: Try to connect to the target again.
Cancel: Remain disconnected from the target
Diagnostic: Run diagnostic utility.
hoping to get some valuable suggestions to work further................
Thanks in advance
Priya......
DISCLAIMER:
-----------
The contents of this e-mail and any attachment(s) are confidential and intended
for the named recipient(s) only.
It shall not attach any liability on the originator or HCL or its affiliates.
Any views or opinions presented in
this email are solely those of the author and may not necessarily reflect the
opinions of HCL or its affiliates.
Any form of reproduction, dissemination, copying, disclosure, modification,
distribution and / or publication of
this message without the prior written consent of the author of this e-mail is
strictly prohibited. If you have
received this email in error please delete it and notify the sender immediately.
Before opening any mail and
attachments please check them for viruses and defect.
-----------
connecting problem with XDS510 USB emulator via JTAG for Davinci DM6446
Started by ●June 27, 2009
Reply by ●June 30, 20092009-06-30
hello ,
i tried my best connecting emulator to other boards but it was not getting connected.
i'll try to contact spectrum digital tech support for further issues.
thanks
priya...
Hello,
>
> I've problem connecting the target via CCS 3.3 .
>
>I use JTAG adapter to connect to target in which I set the switches to
>default state(ie. All OFF state)
>
>It give the following error:
>
>Error connecting to the target:
>
>Error 0x80000240/-180
>
>Fatal Error during: Initialization, OCS,
>
>This error was generated by TI's USCIF driver.
>
>SC_ERR_CTL_NO_TRG_POWER
>
>The controller has detected a target power loss.
>
>The user may have failed to turn-on or connect its source.
>
>Sequence ID: 0
>
>Error Code: -180
>
>Error Class: 0x80000240
>
>I/O Port = 0
>
>Board Name: DM6446 XDS510 Emulator
>
>Cpu Name: ICEPICK_C_0
>
>Abort: Close Code Composer Studio.
>
>Retry: Try to connect to the target again.
>
>Cancel: Remain disconnected from the target
>
>Diagnostic: Run diagnostic utility.
>
>hoping to get some valuable suggestions to work further................
>
>Thanks in advance
>
>Priya......
>
>DISCLAIMER:
>-----------
>
>The contents of this e-mail and any attachment(s) are confidential and intended for the named recipient(s) only.
>It shall not attach any liability on the originator or HCL or its affiliates. Any views or opinions presented in
>this email are solely those of the author and may not necessarily reflect the opinions of HCL or its affiliates.
>Any form of reproduction, dissemination, copying, disclosure, modification, distribution and / or publication of
>this message without the prior written consent of the author of this e-mail is strictly prohibited. If you have
>received this email in error please delete it and notify the sender immediately. Before opening any mail and
>attachments please check them for viruses and defect.
>
>-----------
_____________________________________
i tried my best connecting emulator to other boards but it was not getting connected.
i'll try to contact spectrum digital tech support for further issues.
thanks
priya...
Hello,
>
> I've problem connecting the target via CCS 3.3 .
>
>I use JTAG adapter to connect to target in which I set the switches to
>default state(ie. All OFF state)
>
>It give the following error:
>
>Error connecting to the target:
>
>Error 0x80000240/-180
>
>Fatal Error during: Initialization, OCS,
>
>This error was generated by TI's USCIF driver.
>
>SC_ERR_CTL_NO_TRG_POWER
>
>The controller has detected a target power loss.
>
>The user may have failed to turn-on or connect its source.
>
>Sequence ID: 0
>
>Error Code: -180
>
>Error Class: 0x80000240
>
>I/O Port = 0
>
>Board Name: DM6446 XDS510 Emulator
>
>Cpu Name: ICEPICK_C_0
>
>Abort: Close Code Composer Studio.
>
>Retry: Try to connect to the target again.
>
>Cancel: Remain disconnected from the target
>
>Diagnostic: Run diagnostic utility.
>
>hoping to get some valuable suggestions to work further................
>
>Thanks in advance
>
>Priya......
>
>DISCLAIMER:
>-----------
>
>The contents of this e-mail and any attachment(s) are confidential and intended for the named recipient(s) only.
>It shall not attach any liability on the originator or HCL or its affiliates. Any views or opinions presented in
>this email are solely those of the author and may not necessarily reflect the opinions of HCL or its affiliates.
>Any form of reproduction, dissemination, copying, disclosure, modification, distribution and / or publication of
>this message without the prior written consent of the author of this e-mail is strictly prohibited. If you have
>received this email in error please delete it and notify the sender immediately. Before opening any mail and
>attachments please check them for viruses and defect.
>
>-----------
_____________________________________