Michael,
I'm not so thin skinned as to be insulted.
I just wrote the fact, I do not know anything about the two emulators being
discussed.
I was originally referring to my experience with other emulators and what a
failure to connect usually meant, (after the appropriate emulator drivers had
been loaded to CCS).
SO no problem at all.
R. Williams
---------- Original Message -----------
From: Michael Dunn
To: Richard Williams
Cc: J J , c...
Sent: Wed, 21 Apr 2010 08:07:38 -0500
Subject: Re: +[c6x]+WINTECH+TDS510PLUSE+Jtag+Emulator
> Richard,
>
> I hope that I did not offend you - that was not my intention.
> When I think about it, I try to keep people's "head in the game" so that
they can troubleshoot. Many of the folks on this list are young and
impulsive.
>
> mike
>
> On Wed, Apr 21, 2010 at 2:29 AM, Richard Williams
wrote:
>
> Michael,
>
> Your right, and I know nothing about the emulators being discussed so maybe I
should just sit back on this problem.
>
> R. Williams
>
> ---------- Original Message -----------
> From: Michael Dunn
> To: Richard Williams
> Cc: J J , c...
> Sent: Wed, 21 Apr 2010 01:54:49 -0500
> Subject: Re: +[c6x]+WINTECH+TDS510PLUSE+Jtag+Emulator
>
> >
> >
> > JJ & Richard,
> >
> > On Wed, Apr 21, 2010 at 1:36 AM, Richard Williams
wrote:
> >
> >
> >
> > J J
> >
> > That sure reads like my 'guess' as to the cause of the problem was
correct.
> >
> > However, since another emulator works, I now suspect the failing emulator
has a problem.
> >
> > R. Williams
> >
> >
> > Being intimately familiar with the XDS510 technology of the emulator and the
fact that Wintech is not known for "simple, user friendly configuration" of
their XDS510 technology emulators [although this is their 'new and
improved' version], I would pursue getting xdsprobe to work before blaming
any hardware.
> >
> > mikedunn
> >
> >
> >
> >
> > ---------- Original Message -----------
> > From: J J
> > To: c...
> > Sent: Tue, 20 Apr 2010 23:08:39 -0700 (PDT)
> > Subject: Re:+[c6x]+WINTECH+TDS510PLUSE+Jtag+Emulator
> >
> > >
> > >
> > > Dear
> > > I was Run xdsprobe .It Does work!!
> > > Errorr Mesage is:
> > >
> > > C:\CCStudio_v3.3\cc\bin>xdsprobe.exe
> > >
> > > -----[Select and reset the controller]---
> > >
> > > This utility will operate on port address '0x0'.
> > > That original port address was aliased to '0x0240'.
> > >
> > > An error occurred while hard opening the controller.
> > >
> > > -----[An error has occurred and this utility has
aborted]--------------------
> > >
> > > This error is generated by TI's USCIF driver.
> > >
> > > The value is `-180' (0xffffff4c).
> > > The title is: `SC_ERR_CTL_NO_TRG_POWER'.
> > >
> > > The explanation is:
> > > The controller has detected a target power loss.
> > > The user may have failed to turn-on or connect its source.
> > >
> > > C:\CCStudio_v3.3\cc\bin>pause
> > > Press any key tocontinue . . .
> >
> >
> >
> > > --
> > www.dsprelated.com/blogs-1/nf/Mike_Dunn.php
> >
> >
> ------- End of Original Message -------
> --
> www.dsprelated.com/blogs-1/nf/Mike_Dunn.php
------- End of Original Message -------
