We are developing an assembler language program for the TMS320C31. The design is being developed using the Code Composer 4.10.36...

We are developing an assembler language program for the TMS320C31. The design is being developed using the Code Composer 4.10.36 development environment. The hardware debugging process is achieved using Spectrum Digitals XDS510PP emulator. We have decided to tackle the problem

Hi guys, I need to generate a sine wave on the C31. This is how I am approaching it, I am writing a C program to generate the ...

Hi guys, I need to generate a sine wave on the C31. This is how I am approaching it, I am writing a C program to generate the sine wave using phasor multiplication. This program returns a range of floating point values which correspond to a sine wave. How do I carry on from he

hi i am lloking for the Code Explorer Debugger earlier made by Go DSP . actually i want to debug the code without using the...

hi i am lloking for the Code Explorer Debugger earlier made by Go DSP . actually i want to debug the code without using the emulator card .. or can you provide me some driver for code composer of parallel port c31 card ... so that i can debug the code in windows environment

hi first of all sorry for putting it on so late on the net ! the problem which i mentioned in the earlier mail regarding th...

hi first of all sorry for putting it on so late on the net ! the problem which i mentioned in the earlier mail regarding th einaccessibility of the glabal variable placed in another file ... i managed to recover the problem . It was due to the the optimization level in the bui

hi i have been coding on the code composer in the emulator . my project contains 4 source files . i have a global variable in...

hi i have been coding on the code composer in the emulator . my project contains 4 source files . i have a global variable in teh file containong main ... but when i try to access it through the sub routine which is present in the other file , in which the global variable is r

Hello Nico, No I did not receive a prior email, so something was amiss there. Yes, both auxiliary arithmetic units can...

Hello Nico, No I did not receive a prior email, so something was amiss there. Yes, both auxiliary arithmetic units can perform simultaneous circular addressing (see examples below). The most likely scenario (for the distorted audio) is that you are trying to

All, We have two target boards (one in-house developed and one COTS Spectrum Digital EZDSP) for the TMS320VC33. The emulator and...

All, We have two target boards (one in-house developed and one COTS Spectrum Digital EZDSP) for the TMS320VC33. The emulator and code composer work fine w/ the EZDSP; however we run into problems on our target board. System TMS320VC33 -120 running in CLKMD0/1 =>

Hello Kuangchua Try using the driver tool from Direct IO. Basicaly the problem with NT/2000 is that the OS is trapping each IO...

Hello Kuangchua Try using the driver tool from Direct IO. Basicaly the problem with NT/2000 is that the OS is trapping each IO access and comparing the IO address to an IO Protection Map (IOPM) if the addresses match up to a set bit in the IOPM an interrupt (a GPF) is set that

Hi, I am using the C31 DSK and the Code Composer and as I am quite new in the DSP field, I have "newbie" questions. How...

Hi, I am using the C31 DSK and the Code Composer and as I am quite new in the DSP field, I have "newbie" questions. How can I calculate the execution speed of the C31? What would be the execution time of the following part of code: for (n=0; n <= (100

Hello, I have the Code Composer 4.10 Sp2, the C31 DSK and the DOS tool which are provided with the DSK. If I understand the...

Hello, I have the Code Composer 4.10 Sp2, the C31 DSK and the DOS tool which are provided with the DSK. If I understand the posts before I can't connect to the DSK with the Code Composer. Is there a possibility to use the .asm files generated by the CC with the DSK3a.exe