JTAG interface of TI DSP

Started by as_partovi in comp.dsp9 years ago 1 reply

Dear all, I want to connect the JTAG pins of the TI's DSP(C6418) to an FPGA and try to download my program into the DSP by asserting the JTAG...

Dear all, I want to connect the JTAG pins of the TI's DSP(C6418) to an FPGA and try to download my program into the DSP by asserting the JTAG pins. In other words, I want to make my own JTAG loader. To do so, I need detail document about JTAG signaling of the TI DSPs. Is it a standard interface? Is it IEEE 1149 or something? Is the standard available? Where can I find a free one? Has anybody body...


JTAG implementation

Started by Giovanni in comp.dsp14 years ago 3 replies

Hello everybody. I'm interested in developing a JTAG system using a FPGA programmed in VHDL. Is there some good source on line that can help me...

Hello everybody. I'm interested in developing a JTAG system using a FPGA programmed in VHDL. Is there some good source on line that can help me in doing that? Where can I found the specification of JTAG standard? Are they free available? If I am OT can you say me that? Thanks a lot


JTAG connection to Blackfin BF533

Started by Jamie Morken in comp.dsp12 years ago

Hi, Does anyone have a schematic showing the hookup to a byteblaster or wiggler compatible JTAG adapter to the BF533? I am not sure what...

Hi, Does anyone have a schematic showing the hookup to a byteblaster or wiggler compatible JTAG adapter to the BF533? I am not sure what pullups or pulldowns to use on the individual JTAG signals. Also there are two different wiggler cables (14pin and 20pin) I have the 20pin cable from Olimex.com: http://www.olimex.com/dev/arm-jtag.html cheers, Jamie


In-circuit flashing via JTAG

Started by IvanC in comp.dsp10 years ago 5 replies

Hi, Our embedded system has several devices which are programmed directly via JTAG (CPLD, XPLD, AVR). We need also to program the flash...

Hi, Our embedded system has several devices which are programmed directly via JTAG (CPLD, XPLD, AVR). We need also to program the flash memory of a TI DSP TMS320C4616 via JTAG, but cannot find any information how to do that. What we can do is to run a DSP application in debug mode using the Code Composer Studio with a JTAG debugger. This application is developed to program the flash of the ...


JTAG Emulator

Started by Anonymous in comp.dsp13 years ago 1 reply

Dear all, I have two questions. 1) Could anyone recommend a low-cost JTAG emulator for PC, that would be compatible with c6000...

Dear all, I have two questions. 1) Could anyone recommend a low-cost JTAG emulator for PC, that would be compatible with c6000 devices 2) Is it possible to program my DM642 evaluation board (the Spectrum Digital model) _without_ using a JTAG emulator? Thanks in advance.


a problem about TS101

Started by Anonymous in comp.dsp10 years ago 5 replies

I have a problem about TS101 ,can somebody help me?Thank you The JTAG can scaned succesfully ,but there was a error happened when I uesed JTAG...

I have a problem about TS101 ,can somebody help me?Thank you The JTAG can scaned succesfully ,but there was a error happened when I uesed JTAG to do simulation ,that is 'An EMUIR scan was attempted ,but the dsp is not ready to accept instruction via JTAG'. I don't kown what's wrong with it.


ADS supports TI JTAG Emulator?

Started by Joonsok Lee in comp.dsp13 years ago 1 reply

I'm goint to debug ARM7TDMI using TI XDS510PP-Plus JTAG emulator. I want to know if it is possible to use XDS510 JTAG emulator under ADS(Arm...

I'm goint to debug ARM7TDMI using TI XDS510PP-Plus JTAG emulator. I want to know if it is possible to use XDS510 JTAG emulator under ADS(Arm Development Suite) environment. Do I need some drivers? Please, Help me.


Communicating with C54CST board without JTAG emulation?

Started by vamsikodavanty in comp.dsp13 years ago 2 replies

Hi, I have a TI C54CST eval board and I do not have any JTAG emulators. I just wanted to know if there was a way to communicate with the board...

Hi, I have a TI C54CST eval board and I do not have any JTAG emulators. I just wanted to know if there was a way to communicate with the board via the COM port on my PC. Is having a JTAG emulator the only way to do this? Thanks - Vamsi This message was sent using the Comp.DSP web interface on www.DSPRelated.com


Install JTAG XDS510pp_plus

Started by Dibyendu Mondal in comp.dsp13 years ago 5 replies

Hi all Today I get JTAG xds510pp_plus but I have find a problem to install it. I have the system: ______________ ...

Hi all Today I get JTAG xds510pp_plus but I have find a problem to install it. I have the system: ______________ |TMS320C6711DSK| PC and the new one: ______________ |TMS320C6711DSK| ( PC(??) so have I use 2 Printer port to connect JTAG,DSP and PC ? DSP JTAG \ / \


DSP JTAG header Connection

Started by lyngan in comp.dsp11 years ago

Hi all, I have some problems about the connection between JTAG header (2x7 pins) and ADI BF533. I had followed the schematics provided by ADI,...

Hi all, I have some problems about the connection between JTAG header (2x7 pins) and ADI BF533. I had followed the schematics provided by ADI, in which construct the JTAG header from BF533 (EMU, TDO, TDI, TRST and TCK pins) using two ADG774ABRQ. However, I failed to connect my board to the USB ICE emulator, an error code 0x80048008 occurs. Did anyone try the ADI JTAG header connection befo...


TMS320R2811 JTAG communication

Started by Korenje in comp.dsp12 years ago 4 replies

Hello, I have built a board with TMS320R2811 on it. When I power it up oscillator works, and on RS pin I can see the watchdog reset as it...

Hello, I have built a board with TMS320R2811 on it. When I power it up oscillator works, and on RS pin I can see the watchdog reset as it is supposed to, so I assume that the core is alive. But I can not communicate with the DSP, through JTAG with XDS510PP+. I connected all the JTAG pins as they are supposed to (according to ezDSP R2812 schematics). I had no problems with my previous board...


TMS320F240 flash program via JTAG

Started by robidp in comp.dsp11 years ago

Dear all, I want to program the TMS320F240 Flash via its JTAG port. TI provides the algorithms used, I want to know how I can take control of...

Dear all, I want to program the TMS320F240 Flash via its JTAG port. TI provides the algorithms used, I want to know how I can take control of the device using JTAG instructions or something else. May you help me? robidp


JTAG Emulator: ICETEK-5100USB2.0 for TI DSP

Started by Howard Long in comp.dsp12 years ago 4 replies

Folks Re: ebay item 8749091151 I received this last week in the UK from Hong Kong. It took only three days to arrive! Early indications...

Folks Re: ebay item 8749091151 I received this last week in the UK from Hong Kong. It took only three days to arrive! Early indications are that it seems to work fine on the C6713 DSK with CCS 3.1, although it seems a bit slower than the embedded JTAG DSK emulator. Still, at less than 20% of the cost of the Spectrum Digital USB JTAG Emulator, it's a bargain. Regards, Howard ...


Debugging with ADI Blackfin without JTAG or EZ-Kit

Started by Ian in comp.dsp14 years ago 5 replies

Hi all, I'd like to do a project using an Analog Devices Blackfin 531/532 but definately won't have access to a JTAG interface and, unless I...

Hi all, I'd like to do a project using an Analog Devices Blackfin 531/532 but definately won't have access to a JTAG interface and, unless I can get the current US$99 EZ-Kit deal here in New Zealand, without the JTAG-USB debug on the AD dev kit. Will it be easy to get the chip running on a custom board? Does anyone have experience like this? I have access to VisualDSP (90 days) so ca...


Problem with Jtag Emulator

Started by tonydeng in comp.dsp10 years ago 3 replies

I recently bought an emulator from China, it is a "TDS510 DSP USB2.0". CCS can't initialise the CPU, so I tested the emulator with xdsprobe.exe (...

I recently bought an emulator from China, it is a "TDS510 DSP USB2.0". CCS can't initialise the CPU, so I tested the emulator with xdsprobe.exe ( the targetis a F2808 CPU on a board that was working fine with a Spectrum's XDS510 emulator and the target PD is connected to 3.3V ). I got the following result, The test for the JTAG IR instruction scan-path length succeeded. The JTAG IR instructio...


Possible to use Blackfin EZ-kit as generic JTAG-emulator?

Started by Anonymous in comp.dsp11 years ago

Hi I have an EZ-Kit lite for the BF533 cpu. It connects to the PC through an undocumented USB interface, which most certainly uses JTAG to...

Hi I have an EZ-Kit lite for the BF533 cpu. It connects to the PC through an undocumented USB interface, which most certainly uses JTAG to the cpu. Could it be so that this USB-interface could connect to an "outside" system, i.e. not the on-board Blackfin? The EZ-kit has a JTAG-connector and the documentation says that if connected the USB-interface is disconnected. Probably it is more or...


LYRTECH PADK (TMSC672x) with JTAG XDS510P PLUS (DigitalSpectrum)

Started by ecliang in comp.dsp10 years ago 2 replies

DEAR ALL Document depicting Connecting to the PADK with XDS510USB JTAG emulator has been reported in public. But Our depart has the...

DEAR ALL Document depicting Connecting to the PADK with XDS510USB JTAG emulator has been reported in public. But Our depart has the board LYRTECH PADK (TMSC672x) and we have a JTAG XDS510P PLUS (DigitalSpectrum) Does any one know if there is a driver that we can use XDS510P PLUS (PRINTERPORT) on LYRTECH PADK? Thank you very Much ecliang


JTAG emulator XDS510PP active LED

Started by eeh in comp.dsp13 years ago 1 reply

Hi, I used JTAG emulator XDS510PP to connect to my target board which has a TMS320C6711 DSP chip. However, the active LED on the emulator does...

Hi, I used JTAG emulator XDS510PP to connect to my target board which has a TMS320C6711 DSP chip. However, the active LED on the emulator does not turn on. I have measure the Power Present PD pin(Pin 5) of JTAG pin header on the target board is 3.3V, and the GND pins are OK. Do anyone know why this happens? Thanks!


Programing with JTAG connector on 6416

Started by Ollagnon in comp.dsp13 years ago 1 reply

I have a card to made with a TEXAS dsp (6416) and I want to know, how can I do to pogram the device directly with the...

I have a card to made with a TEXAS dsp (6416) and I want to know, how can I do to pogram the device directly with the JTAG-Emulator connector. It seems that we have to bye an interface. Is someone know anything about it?


CCS compatible JTAG interfaces

Started by Anonymous in comp.dsp14 years ago 3 replies

Does anybody know of a reasonably priced JTAG interface which works with the Texas Code Composer Studio. All the ones I have found so far...

Does anybody know of a reasonably priced JTAG interface which works with the Texas Code Composer Studio. All the ones I have found so far cost $3,000+ !!! Regards Andy Please send any email to andy.robertson1@ntlworld.com as I don't often get the opportunity to browse newsnet.