DSPRelated.com

External Clock level DSP56374

Started by asgr...@xs4all.nl in Freescale DSPs11 years ago 1 reply

Hello All, I'm trying to find out if the DSP56374 is "5 Volt" tolerant on the input EXtal pin. The DSP56371 is according to the UG - but I'm not...

Hello All, I'm trying to find out if the DSP56374 is "5 Volt" tolerant on the input EXtal pin. The DSP56371 is according to the UG - but I'm not sure if the DSP56374 is as I'd like to use an external XO. All other inputs are 5V tolerant - but I can't find anything on the clock. Does anybody know? brgrds, Paul


Looking for Freescale Symphony Soundbite

Started by cine...@passport.ca in Freescale DSPs14 years ago 6 replies

Hello, Trying to buy a Symphony Soundbite audio development board but can't find a distributor with one in stock. Would anyone know where I might...

Hello, Trying to buy a Symphony Soundbite audio development board but can't find a distributor with one in stock. Would anyone know where I might find one beyond the obvious distributors? Thanks, Jim


Need ASRC example code for 567xx

Started by wede...@gmail.com in Freescale DSPs14 years ago 3 replies

Hi, I was wondering if anyone out there has successfully used the ASRC (asynchronous sample rate converter) for any of the dual core 567xx...

Hi, I was wondering if anyone out there has successfully used the ASRC (asynchronous sample rate converter) for any of the dual core 567xx chips? If so, do you have some sample code that would shed some light on the intented use of this coprocessor? I should say that, following the manual and using the eval board, I have it in a quasi-working state using motherboard S/PDIF in/out on the ...


OLD MOTOROLA DSP56 EVM's and WINDOWS 7

Started by skel...@tiscali.co.uk in Freescale DSPs14 years ago 3 replies

Hi, I have a MOTOROLA DSP56363 and a MOTOROLA DSP56367 EVM and am using with the supplied degugging software interface supplied with the Motorola...

Hi, I have a MOTOROLA DSP56363 and a MOTOROLA DSP56367 EVM and am using with the supplied degugging software interface supplied with the Motorola EVM's and provided by Domain Technology. I've used both these EVM's sucessfully on varied PC platforms from WINDOWS 3.1 through to WINDOWS 7 (32 bit). I've now trying to run them, without sucess, on a 64 bit Windows 7 platform. I've tried all the var...


Memory switch in DSP56303

Started by pal_ingenieria in Freescale DSPs15 years ago 2 replies

Dear folks, As you know, after a RESET, MS bit in the OMR is 0 by default, so the memory configuration consist of the following: 4K of program...

Dear folks, As you know, after a RESET, MS bit in the OMR is 0 by default, so the memory configuration consist of the following: 4K of program memory (0x0-0xFFF), 2K of X data and 2K of Y data. After RESET, I load the program memory by using the bootloader as usual. After that, my program sets the MS bit (bit 7) in the OMR in order to change the memory configuration to 2K of program memory (0x0...


Regarding Daughter Board DSPX72YDBZE

Started by Gopalkrishna Dandagi in Freescale DSPs15 years ago 2 replies

Hi Christian The Information regarding Regarding Communication of I2C in DSPA56721 with PIC16F886 given by you is very much useful for me thank...

Hi Christian The Information regarding Regarding Communication of I2C in DSPA56721 with PIC16F886 given by you is very much useful for me thank you. But now I am using Mother board DSPAUDIOEVMMB1E and Daughter board DSPX72YDBZE. I found the DSPAUDIOEVM-USER GUIDE in the freescale site but the user guide for the Daughter board DSPX72YDBZE is not found. Hence the development is struck up. From w...


Regarding Communication of I2C in DSPA56721 with PIC16F886

Started by Gopalkrishna Dandagi in Freescale DSPs15 years ago 1 reply

Hi, I am using Free scale DSPA56721 80 pin for one of application using PIC16F886 microcontroller. Now i want to communicate with DSPA56721...

Hi, I am using Free scale DSPA56721 80 pin for one of application using PIC16F886 microcontroller. Now i want to communicate with DSPA56721 from PIC16F886 through I2C protocol. How to configure I2C communication protocol in DSPA56721 ? and what are all the steps i need to follow ? Thank you Warm Regards, Gopalkrishna.D | Software Engineer |Wireless and Automotive products


Hour counter

Started by albe...@yahoo.it in Freescale DSPs15 years ago 1 reply

Hello, I'm tring to store a number in the flash memory but the SetWordFlash() gives me every time error 9 (myTempByte) and the flash is not...

Hello, I'm tring to store a number in the flash memory but the SetWordFlash() gives me every time error 9 (myTempByte) and the flash is not written. I've declared a global "const int myContaOre" variable to store the value. Setwordflash is the function of the bean to reprogram teh internal flash. where is the prblem? why the procedure does not write the location? const int myContaOre; myT...


Writing to External Ram on 56720 dev board

Started by Pete Johnston in Freescale DSPs15 years ago 2 replies

Hi Guys Sorry for emailing you direct but the forum won't let me in at the moment. I'm trying to write to the external SDRAM SRAM and FLASH...

Hi Guys Sorry for emailing you direct but the forum won't let me in at the moment. I'm trying to write to the external SDRAM SRAM and FLASH as per the as per the extract from the DSP56720BUG.pdf below. I think need to set up the EMC to match the Chips used and a Memory Map of where they live. Do you know of any example code in Assy that makes use of this external memory? BTW C...


Downloading Aifs and Wavs to 56720 Dev boards. using symphony studio

Started by pdj...@blueyonder.co.uk in Freescale DSPs15 years ago 2 replies

Does anyone know of any documentation regarding downloading wavs or aiffs down to either DSPX72YDBZE 56720 Dev Boards external ram or SPI/I2C...

Does anyone know of any documentation regarding downloading wavs or aiffs down to either DSPX72YDBZE 56720 Dev Boards external ram or SPI/I2C eprom (and then copying it in) using symphony studio. Thanks Pete


Ask a Question to the DSPRelated community

To significantly increase your chances of receiving answers, please make sure to:

  1. Use a meaningful title
  2. Express your question clearly and well
  3. Do not use this forum to promote your product, service or business
  4. Write in clear, grammatical, correctly-spelled language
  5. Do not post content that violates a copyright