Hi, all: I encountered an annoying problem on SCI module(c2000 F2812) in my project.Iused SCIb to send and receive message. Well when I...

Hi, all: I encountered an annoying problem on SCI module(c2000 F2812) in my project.Iused SCIb to send and receive message. Well when I sending the message I turned the RX off(RXENA=0), after sending finishes, the RX is turned on to receive some feedback.I noticed that the RX state register RXST shows frame error(FE=1) before the sending finished, but the RX is turned off at this moment. ...

I have a program that runs from SRAM (mapped to address 0x100000) It worked fine on ccstudio 3.1 with serial connection to ezdspf2812. I...

I have a program that runs from SRAM (mapped to address 0x100000) It worked fine on ccstudio 3.1 with serial connection to ezdspf2812. I installed version 3.3. of code composer studio. I setup program to continue bh-usb510-c28xx.. I connected the blackhawk JTAG (and disconected the serial port) from ezdsp. The problem now is that I cannot run a program from the SRAM. We have a 64K SRAM on...

Hi, I'm trying to learn programming the F2812 using my DSP Board (eZdspF2812 from Spectrum Digital) for my Term Project. I need to use its...

Hi, I'm trying to learn programming the F2812 using my DSP Board (eZdspF2812 from Spectrum Digital) for my Term Project. I need to use its PWM generators and ADC. I looked at the PWM Example of TI (sprc097) and ran it on the Board succesfully. My questions are: 1- What do i need to do in order to make the DSP run the example while the Board isn't connected to a computer?(The code sh...

Hi all, I m working on texas dsp TMS320F2810 . We are connecting Texas dsp and Arm 73 ic through can . Now i m facing problem such that From...

Hi all, I m working on texas dsp TMS320F2810 . We are connecting Texas dsp and Arm 73 ic through can . Now i m facing problem such that From dsp side data gets transmitted. but i m not able to recevice data from ARm side. i m using spra876a.zip from this using RXLOOP.c program and can clock set to 50khz. from both side. Plz. help me to solve this problem Thanks in advance. ...

I have a question about what should happen after a watchdog reset. I'm using CCS 3.1 and a F2812 eZdsp board. After I flash the chip, The PC is...

I have a question about what should happen after a watchdog reset. I'm using CCS 3.1 and a F2812 eZdsp board. After I flash the chip, The PC is at 3DC000, from this point, I hit run and my code begins executing. I purposely have a watchdog reset in there. When this watchdog times out the reset occurs but never gets back to my code. Once I hit halt, the PC is at 3FFC00. It stays there forever. ...

I am trying to establish connection between two can board (ie. two cpu).I have written a CAn transmit code. According to me i feel all...

I am trying to establish connection between two can board (ie. two cpu).I have written a CAn transmit code. According to me i feel all initializations are done properly. All register too reflect as i can see them using jtag emulator.My program wait for ACK so it get struck there. But i want to monitor waveform on my tranmit pin of CAN AS per my code i have written msg box data as high low so i can...

please help me... i have TMS2812 that connected to computer via serial port RS232. When i choose F2812 XDS510 Emulator in CCS system...

please help me... i have TMS2812 that connected to computer via serial port RS232. When i choose F2812 XDS510 Emulator in CCS system configurations setup, i found some problem when i start using CCS that problem is show message below : Error connecting to the target: Error 0x80000240/-2092 Fatal Error during: Initialization, OCS, Device driver: Emulation Connection Loss Detected on Ta...

Hi, I am using TMS320F2812's McBSP in ClockStop Mode (SPI mode). I have the settings as mentioned in the Chapter 2.3 (SPI Protocol)...

Hi, I am using TMS320F2812's McBSP in ClockStop Mode (SPI mode). I have the settings as mentioned in the Chapter 2.3 (SPI Protocol) in the SPRU061B. I am able to see the data transmitted on the DX pin and the FSX signal (Chip Enable signal) on the FSX pin of the board. My issue is that, I am not able to see the clock signal on CLKX pin, when the data is being transmitted on my oscillo...

Please help me, i'm a beginner for DSP and i need your helo to solve my problem. one week ago, I have bought DSP CY-MSK2812 from site...

Please help me, i'm a beginner for DSP and i need your helo to solve my problem. one week ago, I have bought DSP CY-MSK2812 from site www.cyclone.com.cn This device include some header and peripheral example in C and gel format. i have try to run some example (especially for ADC) in Dev-C++, i met much error. This error cause by some keyword that used in header. This keyword is cregister and...

Hi guys I am noobie in F2808, I was working on it for 2 months only. I need help. I have written my application in C and using CCStudio...

Hi guys I am noobie in F2808, I was working on it for 2 months only. I need help. I have written my application in C and using CCStudio 3.1. I am facing odd problem here. Whenever I run any code I get following error. That mean I am missing Clock :( if (SysCtrlRegs.PLLSTS.bit.MCLKSTS != 0) { // Missing external clock has been detected // Replace this line with a call...