Beware, though, that a watchdog reset is not as clean as a powerup reset in= terms of reinitilizing the registers of the DSP. A better solution...

Beware, though, that a watchdog reset is not as clean as a powerup reset in= terms of reinitilizing the registers of the DSP. A better solution to cons= ider is tying one of the GPIO pins to the voltage supervior chip such that = pulling that pin low results in a true hardware reset. Cheers, Beat. On 11/26/08, Alain SALMETOZ wrote: > For our projects, we simply force t

Can any one please tell me what is the assembly command to reset(not for halt) F2812 DSP.? I searched the manual, but unable to find it....

Can any one please tell me what is the assembly command to reset(not for halt) F2812 DSP.? I searched the manual, but unable to find it. Anticipating your reply. OMAP35x EVM jump-starts low-power apps The modular and extensible OMAP35x Evaluation Module (EVM) enables developers to start building applications based on the OMAP35x architecture: http://www.DSPRelated.com/omap35x

Hi all, How do I make the Timer and EV compare register values to zero, before halt the processor? I am working in TMS320F2812 eZDSP starter...

Hi all, How do I make the Timer and EV compare register values to zero, before halt the processor? I am working in TMS320F2812 eZDSP starter kit. I loaded my program which has some value in CMPR and EV Timer registers in DSP, I wish to bring those values to zero before going to halt the DSP in code composer. How do I achieve that? Will it be possible to send inputs from the key board when the ...

Hi everybody,,, Can anyone Plz explain my doubt.... Each I2C module has its own unique address,,I am using F2812Controller in that one...

Hi everybody,,, Can anyone Plz explain my doubt.... Each I2C module has its own unique address,,I am using F2812Controller in that one I2C peripheral is there,wre can i get this I2C module address? Regards, Srinu Check Out Industry's First Single-Chip, Multi-Format, Real-Time HD Video Transcoding Solution for Commercial & Consumer End Equipment: www.ti.com/dm6467

I am interesting in motor control. And I used 8-bit microcontroller=20 to control ACI motor in inverter before.=20 Now I find the DSP is...

I am interesting in motor control. And I used 8-bit microcontroller=20 to control ACI motor in inverter before.=20 Now I find the DSP is rational choice to control ACIM or PMSM,=20 because the control system and algorithms are getting more and more=20 complicated. And the TMS320LF2812 device of TI is the most popular. But I am a newcomer in DSP, it is hard for me to step forward, to=20 m...

Hello, I am using TMS320F2812 processor along with Code Composer Studio and XDS510USB Emulator. I have got my code running in flash so I have...

Hello, I am using TMS320F2812 processor along with Code Composer Studio and XDS510USB Emulator. I have got my code running in flash so I have got a restriction of setting of maximum of 2 hardware breakpoints in my code. In my code an application/process is hooked to timer2 interrupt which is set for getting called every XYZ milliseconds and my objective is to confirm that the application is ...

Hello, I am working on TMS320F2808 DSP controllor Starter kit from Spectrum Digital. I am working on the SPI peripheral. I have configured DSP...

Hello, I am working on TMS320F2808 DSP controllor Starter kit from Spectrum Digital. I am working on the SPI peripheral. I have configured DSP starter kit as SPI slave and Another master keeps sending some standard data pattern to slave and slave too sends particular data pattern to Master. I wouldlike to know weather the SPI line SPISTE is it Edge triggered or Level triggered. Suppose Master ...

Hi Dhaval, it seems we develop similar applications.. If you are always on this group reply me so we could exchange some...

Hi Dhaval, it seems we develop similar applications.. If you are always on this group reply me so we could exchange some informations. Thanks, Raffaele > Hi Everybody, > > I am a new member to this group. Thanks to the mod/owner who started > this yahoo group. I am a newbie to DSP programming and just commenced > my project using TMSDSPF2812. I have to develop V/F control inverter

Dear all, First of all, Let me thank this discussion group for being active and accepted me as a member. I am new to DSP . Having following...

Dear all, First of all, Let me thank this discussion group for being active and accepted me as a member. I am new to DSP . Having following doubts in PWM generation. *1)* If I generate PWM for the same frequency and duty ratio using Event Manager A and Event Manager B and observe the PWMS in scope, I saw that the PWMs using EV B is phase shifted by 284ns from PWMs using EV A. why t...

When I try to flash my F28335 I get the following error: "Your BIOS Version is not compatible with this RTA Version.? It must? be? version?...

When I try to flash my F28335 I get the following error: "Your BIOS Version is not compatible with this RTA Version.? It must? be? version? 5.2.x.x.? Your? version looks to? be? :? a? non BIOS program , or possibly BIOS 490 or earlier" What does this mean and how do I fix it? Regards, Joe ?