I get the following warnings when I try to build my project: warning: relocation overflowed; the 17-bit relocated address 0x11e66 is too ...

I get the following warnings when I try to build my project: warning: relocation overflowed; the 17-bit relocated address 0x11e66 is too large to encode in the 16-bit field (type = 'RE_XSTFLD' (16406), file = "C:\\dev\\gen5\\ML\\MLtest_16\\Debug\\Configuration1cfg.obj", offset = 0x00000000, section = ".gblinit") warning: relocation overflowed; the 17-bit relocated address 0x11866 i...

Hi, I am having a problem running a program from flash memory on the=20=20 DSK5510 and I was hoping someone could give me a pointer (no...

Hi, I am having a problem running a program from flash memory on the=20=20 DSK5510 and I was hoping someone could give me a pointer (no pun=20=20 intended - really) as to what I might be doing wrong. I am using the=20=20 eDSP DSKAudio4 4-channel audio daughterboard for audio I/O and Code=20=20 Composer 3.2 with DSP/BIOS. My problem is that the exact same compilation of my software works=...

Sir, i have to use TIMER0 module for a code.But i dont know how to initialise the Timer module.While going through the CSL library functions...

Sir, i have to use TIMER0 module for a code.But i dont know how to initialise the Timer module.While going through the CSL library functions i came across a parameter "TIMER_Handle hTimer", What is the significance of this parameter?.Pls mail me a sample code to initialise the TIMER0 and the significance of TIMER_Handle hTimer parameter.............

Hi , I am working with TMS320C5509A emif and facing a similar problem. When I write address for CE spaces no Chip select is generated. By...

Hi , I am working with TMS320C5509A emif and facing a similar problem. When I write address for CE spaces no Chip select is generated. By default CE signal for CE space CE1 is generated for any address. I am writing address as shown below. *(int*)0x400000 = 0xFFFF; // CE space 2 as I am using in word mode config Also if I write statement where should i be able to see the data in Memo...

Hi, I am new to the DSS C55x series from TI and I am trying to interface the C5502 with a PC using the UART. I bought the evaluation board...

Hi, I am new to the DSS C55x series from TI and I am trying to interface the C5502 with a PC using the UART. I bought the evaluation board and they show an example code with their BSL. The problem is I want to make use of the CSL and there's nothing about it in terms of examples... Does anyone have an example code on How setup the CSL for the UART on the C5502.. Any code would be appr...

Hi Dileepan, I am working with TMS320C5509A emif and facing a similar problem. When I write address for CE spaces no Chip select is...

Hi Dileepan, I am working with TMS320C5509A emif and facing a similar problem. When I write address for CE spaces no Chip select is generated. By default CE signal for CE space CE1 is generated for any address. I am writing address as mentioned by you. Also if I write statement *(int*)0x400000 = 0xFFFF; // CE space 2 as I am using in word mode config where should i be able to see the data ...

i am working with c5510 on voice application, i tried to include dsplib.h but an error massage (could not open source file "Dsplib.h") how to...

i am working with c5510 on voice application, i tried to include dsplib.h but an error massage (could not open source file "Dsplib.h") how to include dsp library to my project? Aliaa Ibrahim Seleem Faculty Of Engineering Computer EngineeringDepartment a...@gmail.com

i need to know how to configure audio device before using (dsk5510_aic23.h) because no out file created #include "switchcfg.h" #include ...

i need to know how to configure audio device before using (dsk5510_aic23.h) because no out file created #include "switchcfg.h" #include #include DSK5510_AIC23_Config setup = {\ 0x0017,\ 0x0017,\ 0x01ff,\ 0x0015,\ 0x0000,\ 0x0000,\ 0x0043,\ 0x0081,\ 0x0001\ }; void main() { DSK5510_AIC23_CodecHandle hCodec; Int16 data; /* Initializ

Hello, all; I'm taking a class that involves the use of C5510 DSK with a 200 MHz TMS320VC5510 DSP processor, and I need to incorporate a...

Hello, all; I'm taking a class that involves the use of C5510 DSK with a 200 MHz TMS320VC5510 DSP processor, and I need to incorporate a Hilbert transform into a project I'm working on involving phase shifting audio. Does anyone have any insights into how I would program this or where I might find additional resources? Thanks in advance... Allan

How does a DMA synchronize to the first element of the McBSP? The McBSP will send events to the DMA on every element transfer, but how does the...

How does a DMA synchronize to the first element of the McBSP? The McBSP will send events to the DMA on every element transfer, but how does the DMA synchronize to an EXTERNAL frame synch (and clock)? Should the McBSP frame interrupt be used to start the McBSP transmitter/reciever? Presently the DMA is started and subsequently the McBSP. The McBSP is started irrespective of the external frame...