hi everybody, i am working MSCAN protocol (v02.15) for the MC9S12D64BCPV(16MHz) MCU....can anybody suggest me that how can we...

hi everybody, i am working MSCAN protocol (v02.15) for the MC9S12D64BCPV(16MHz) MCU....can anybody suggest me that how can we know the Succesfull Transmission of the particular CAN message. after the succesful transmission of the CAN message,we can enable the CANTXIE interrupt..but how can we know the successful transmission of the message... plz provi...

Has any one used TEL_AEC bean with 8013? My understanding is that TEL_AEC needs external memory while 8013 does not support. Please inform.

Has any one used TEL_AEC bean with 8013? My understanding is that TEL_AEC needs external memory while 8013 does not support. Please inform.

I am trying to use 8013's SPI to send a 16 bits long info to a slave device. I am wondering if I could use SendChar command to do it. My...

I am trying to use 8013's SPI to send a 16 bits long info to a slave device. I am wondering if I could use SendChar command to do it. My concerns is that a Char is only 8 bits long. Can I use SendChar twice to achieve 16 bits long info? if not, how can I send 16 bits word by using SPI? Please help and thanks in advance.

Under 56F8013AVFE bean, there are two places to specify the clock frequency. One is Oscillator Frequency default at 8MHz and another is...

Under 56F8013AVFE bean, there are two places to specify the clock frequency. One is Oscillator Frequency default at 8MHz and another is System Clock which can be set to 32MHz. I need to get 32MHz MIPS for the calculation and wondering if the 32MHz System Clock is good enough.

Hi, I am new to DSP world and know nothing about the embedded software development so far. I am targeting for DSP56L307 chip. I am...

Hi, I am new to DSP world and know nothing about the embedded software development so far. I am targeting for DSP56L307 chip. I am wondering if anyone who has the development experience of this chip can give me highlights of the development environment and RTOS that can run best on the chip. Is CodeWarrior compatible with this chip? Do I have to buy a command converter? what kind o...

Hi I want to address each pin of GPIO port serperately (PortA in 56F8323) in C porgramming. Can some one provide me the header file or sample...

Hi I want to address each pin of GPIO port serperately (PortA in 56F8323) in C porgramming. Can some one provide me the header file or sample program for the same. Thanks in advance. Ravi GE India Innovation Centre Hyderabad, India

Hi All We are using MC56F8323EVM. We are trying to do serial communication for last three days without any success. We tried with both SCI0...

Hi All We are using MC56F8323EVM. We are trying to do serial communication for last three days without any success. We tried with both SCI0 and SCI1. We are able to receive data through serial communication, but not able to transmit anything. Please give us the complete procedure with sample application if any for transmission. When we try to use the transmit pins of both port as general p...

Hi, I have a couple of questions related to interfacing the SPI module (DSP56858) to a temperature sensor (TMP122:...

Hi, I have a couple of questions related to interfacing the SPI module (DSP56858) to a temperature sensor (TMP122: http://focus.ti.com/lit/ds/symlink/tmp122.pdf ). The TMP122 has a single I/O line whereas the DSP uses two separate lines, MOSI and MISO. Please tell me if this is feasible to use with the DSP: Tying MOSI and MISO together and tri-stating MOSI each time I wanted to r...

Hi everybody, im using the FlexCan Module from 56f8345 Processor and it works under=20 normal conditions fine, but somtimes some ID_low...

Hi everybody, im using the FlexCan Module from 56f8345 Processor and it works under=20 normal conditions fine, but somtimes some ID_low register changes its=20 value(0x5b14) in an unpropper way i.e. it not fit my former=20 Acceptance mask(0xFFEFFE0E) and ID(0x00180124). We can generate the error by transmitting as much messages as=20 possible to the DSP (i.e. we are running at 125kb and se...

Hi everybody, I've been looking in the data sheets for the Immediate Long Addressing Mode (#> ) but I'm not sure I've understood it...

Hi everybody, I've been looking in the data sheets for the Immediate Long Addressing Mode (#> ) but I'm not sure I've understood it clearly. Is move #> 192,x1 a valid instruction and what would be its result ? Thanks in advance for your help. Best regards -- St?phane Lesoinne -- St?phane Lesoinne Assistant INTELSIG group - D?partement E.E.I. Universit? de Liege B28 B-