Hi, Did a search on the dsp site, and couldn't find an article that matched my issue specifically. I have an in house designed board with...

Hi, Did a search on the dsp site, and couldn't find an article that matched my issue specifically. I have an in house designed board with a 21065L and the JTAG connector made available. Similar to the eval board. On the 21065L, we have connected a RT49LV4096A flash. We may even go up in size, or another one, but the HW interconnect between the 21065L

Hello all, I am trying to connect two ADSP-21065L EZ-Lab. I have a problem in finding the Hardware Interface between the two...

Hello all, I am trying to connect two ADSP-21065L EZ-Lab. I have a problem in finding the Hardware Interface between the two processors. It is stated in the ADSP-21065L User's Manual for particular enviroments that the pins must be connected between the two process

I have a rather embarrassing question. I have been able to do division easily using the divq method in assembler in previous DSPs,...

I have a rather embarrassing question. I have been able to do division easily using the divq method in assembler in previous DSPs, but I can't figure out how to do it in the 21065L assembler. So far, I have been able to compute by hand the 1/n for a number, then do a multiply in 21065l, but now I have numbers that change, meaning variables ins

Hi, I am trying to get a talkthrough program working on the DSP-21065L EZ-Kit Lite, using VisualDSP++ 3.5.3.0. My code is from...

Hi, I am trying to get a talkthrough program working on the DSP-21065L EZ-Kit Lite, using VisualDSP++ 3.5.3.0. My code is from the BP project, located under C:/VisualDSP++3. 5for32-Bit/21k/EZ-Kits/21065L/Demos/. I had to modify the following two lines in the LDF-f

> -----Urspr?ngliche Nachricht----- > Von: sanglierv [SMTP:] > Gesendet am: Freitag, 24. September 2004 11:33 > An: >...

> -----Urspr?ngliche Nachricht----- > Von: sanglierv [SMTP:] > Gesendet am: Freitag, 24. September 2004 11:33 > An: > Betreff: [adsp] ADSP-21065L hangs > > Hi, > > I am trying to get a talkthrough program working on the DSP-21065L

I would like to know if there is some procedure for booting an ADSP- 21065L without using the default boot-kernel included in...

I would like to know if there is some procedure for booting an ADSP- 21065L without using the default boot-kernel included in VisualDSP++. I do not have an evaluation board. I made my own PCB card with RAM, EPROM, codec, and the DSP. However, the 21065L loader is very fancy

I've just gone over the differences between the new Rev. C and the old Rev. B datasheets for the 21065L, and this is what changed: ...

I've just gone over the differences between the new Rev. C and the old Rev. B datasheets for the 21065L, and this is what changed: - In the general description part, the Rev. B datasheet states that "the ADSP-21065l offers the highest performance by a 32-bit DSP - 66 MIPS

It seems that Digikey is going to stop selling ADSP-21065 development kit ADDS-21065L-EZLITE. When I check the availability of this item this...

It seems that Digikey is going to stop selling ADSP-21065 development kit ADDS-21065L-EZLITE. When I check the availability of this item this legend is shown: "Part will become a non-stocking item when stock is depleted; minimums will apply" It sounds like that kit is not being manufactured. Does any of know if ADSP-21065L is near the EOL? Regards Jose

Hi i had posted a question regarding timing requirements (Sub: Hardware : 21065L - Codec Interface(msg no. 1484)). i might reach a...

Hi i had posted a question regarding timing requirements (Sub: Hardware : 21065L - Codec Interface(msg no. 1484)). i might reach a conclusion, if the RFS assertion clock edge is known. i will explain it as follows. i wish to interface a codec with 21065L in multichannel mode. I

Hello, I am using ADDS-21065L-EZLITE as the "signal generator" for testing the project I am working on. I want to feed...

Hello, I am using ADDS-21065L-EZLITE as the "signal generator" for testing the project I am working on. I want to feed my DUT (device under test, another ADDS-21065L-EZLITE) with both the analog version and the digital version of the test data, gener

JaaC wrote: >I don't understand why the output of the ADSP-21065L-EZ-LITE sounds very >low, even when running the "TalkTrhu"...

JaaC wrote: >I don't understand why the output of the ADSP-21065L-EZ-LITE sounds very >low, even when running the "TalkTrhu" like programs. I don't know the ADSP-21065L-EZ-LITE specifically, but if it has a CODEC like the one on the 2189 EZ-LITE, there a

I am new to use ADSP 21065L and i have some problems about using it. Please help me! I have a sharc ADSP 21065L, visual dsp++ 2.0...

I am new to use ADSP 21065L and i have some problems about using it. Please help me! I have a sharc ADSP 21065L, visual dsp++ 2.0 for sharc dsp, and DSP21k-32 Toolkit. Now I want to do that: 1. I want to write a c code at host to access DSP's memoy. ex: I wnat to write so

Hi! I'm having a problem with my thesis. I need to know how to use the external memory of ADSP-21065L. My thesis is about MP3 Decoder using...

Hi! I'm having a problem with my thesis. I need to know how to use the external memory of ADSP-21065L. My thesis is about MP3 Decoder using ADSP-21065L with audio enhancements. An MP3 file should come from an external memory, i.e. SDRAM, SD card. Now I don't know how to interface this to the dsp board. I would really appreciate any help from you. Thank you!

Is anybody have (sdram_kernel.asm) for EZ-KIT 21065L ???

Is anybody have (sdram_kernel.asm) for EZ-KIT 21065L ???

hello, does anyone have a good tutorial for "mixed c" programming with the 21065l from ad. any kind of help would be great ...

hello, does anyone have a good tutorial for "mixed c" programming with the 21065l from ad. any kind of help would be great desperated dsp programmer!

Hi, everyone. I've posted this to comp.dsp as well. Ideas welcome... I'm having some problems using/understanding the 21065L...

Hi, everyone. I've posted this to comp.dsp as well. Ideas welcome... I'm having some problems using/understanding the 21065L SHARC, and I wonder if anyone has any insights: 1. Referencing External Memory I'm developing an application that stores data in an extern

With SHARC ADSP-21065L we are attempting to use the host interface with transfers through the EPBx buffers in single-word...

With SHARC ADSP-21065L we are attempting to use the host interface with transfers through the EPBx buffers in single-word transfers as described in ADSP-21065L SHARC User’s manual ver. Sept. 8 1998 page’s 8-18 thro

am new to programming in adsp 21065l i have following questions 1-the document gives assembly files for configurating i2s port.it doesnot...

am new to programming in adsp 21065l i have following questions 1-the document gives assembly files for configurating i2s port.it doesnot give the complete project.i shall be grateful if anyone can upload complete vdsp project for interfacing i2s compatible audio codec to adsp 21065l via i2s ports 2-documents that are helpful in this regard 3-an overview of the interfacing SPORT with A...

Hi, I'm developing a program that analyzes babies'cry. I'm using an 21065L ADSP and I'm programming in C++. Now, I need...

Hi, I'm developing a program that analyzes babies'cry. I'm using an 21065L ADSP and I'm programming in C++. Now, I need to use a deque (STL) to implement a pitch algorithm. However, I've been experiencing some problems. Are there any limitation

I'm interested in a target design that bridges an Atmel ATMega128 and an ADSP-21065L through the DSP host port. I don't see any...

I'm interested in a target design that bridges an Atmel ATMega128 and an ADSP-21065L through the DSP host port. I don't see any *major* hurdles here, but thought I'd go ahead and ask.. 1. Has anyone here done this? 2. If so, how did it go? Thanks.