Hai all, i am working in a card which involves SPI communication between ADSP-BF531 and ADSP-BF533.when i perform SPI Master mode ...

Hai all, i am working in a card which involves SPI communication between ADSP-BF531 and ADSP-BF533.when i perform SPI Master mode communication(Transmission) on BF531,i am not able to see the SPI clock on the pin. i am able to get the SPI clock if i run the code on BF533(with header file and ldf file modification ). i am bit confused of this pe

i am working in a card which involves SPI communication between ADSP-BF531 and ADSP-BF533.when i perform SPI Master...

i am working in a card which involves SPI communication between ADSP-BF531 and ADSP-BF533.when i perform SPI Master mode communication(Transmission) on BF531,i am not able to see the SPI clock on the pin. i am able to get the SPI clock if i run the code on BF533(with header file and ldf file modification ). >>>>>>>>>>> do you mean that the same SPI code wor

Dear All, I am new to the group. I wanted to know if the PPI Interface of BF531 can be used to interface to a Standard...

Dear All, I am new to the group. I wanted to know if the PPI Interface of BF531 can be used to interface to a Standard Printer. If anyone has done it, please inform. Regards, Chinmoy.

Hi, I had a question regarding loading a code built for BF533 on BF531. If the code is larger than the memory size of BF531, does...

Hi, I had a question regarding loading a code built for BF533 on BF531. If the code is larger than the memory size of BF531, does it automatically move to SDRAM?? thanks regards Navitha

Hi, I wish to configure my BF531 to work at max CCLK of 400MHz and max SCLK of 133MHz. Two options :- 1. I can use a...

Hi, I wish to configure my BF531 to work at max CCLK of 400MHz and max SCLK of 133MHz. Two options :- 1. I can use a 8MHz crystal. Set DF bit to 1. Set the multiplier (MSEL[5:0]) to 50 to get VCO = 400MHz. Set Core Clock Divider to 1 (CSEL[1:0]

Hi, I plan to make my own board based on BF531. I want to use a low cost video decoder chip such as ADV7180, but BF533 Ez-Kit Lite uses...

Hi, I plan to make my own board based on BF531. I want to use a low cost video decoder chip such as ADV7180, but BF533 Ez-Kit Lite uses ADV7183. ADV7183 has 3 A/D converter and runs with 27 MHz crystal. ADV7180 has only one A/D converter and runs with 28.6363 MHz crystal. (I should use different crystals for video chip and the DSP.) And, TVP5146 from TI is also compatible with BF531...

Hi, I wish to configure my BF531 to work at max CCLK of 400MHz and max SCLK of 133MHz. Two options :- 1. I can use a 8MHz crystal. Set DF...

Hi, I wish to configure my BF531 to work at max CCLK of 400MHz and max SCLK of 133MHz. Two options :- 1. I can use a 8MHz crystal. Set DF bit to 1. Set the multiplier (MSEL[5:0]) to 50 to get VCO = 400MHz. Set Core Clock Divider to 1 (CSEL[1:0] = 00) to get CCLK = 400MHz. Set System Clock Divider to 3 (SSEL[3:0] = 0011) to get SCLK = 133.33MHz. I think SCLK will be by itself rounded off

dear all: How to use 32K on-chip-instruction ROM in BF531/532? Does it OTP type or flash type? I found that these ROM...

dear all: How to use 32K on-chip-instruction ROM in BF531/532? Does it OTP type or flash type? I found that these ROM space have been allocated to some output section by expert linker. Does it just the boot rom? I cann't find any information about th