Hi, I am making a blackfin 533 board and was wondering about the JTAG header. I don't have the 14pin JTAG cable used on the STAMP...

Hi, I am making a blackfin 533 board and was wondering about the JTAG header. I don't have the 14pin JTAG cable used on the STAMP boards, but I do have a 20pin cable that is apparently "wiggler" compatible: http://www.olimex.com/dev/arm-jtag.html Would this cable work?

Hi Everbody, I am going to use BF532 and I will need Emulator ... But it's expensive you know... I have JTAG Cable that I used in my previous...

Hi Everbody, I am going to use BF532 and I will need Emulator ... But it's expensive you know... I have JTAG Cable that I used in my previous project to program my CPLD. Shortly I have XILINX JTAG Program cable... I want to clear that ; Can I use this XILINX JTAG cable to emulate BF532 with adding any connection and/or modification ??? Is this possible?? Thank you in advance .... ...

Hi all, I have some problems about the connection between JTAG header (2x7 pins) and ADI BF533. I had followed the schematics provided by ADI,...

Hi all, I have some problems about the connection between JTAG header (2x7 pins) and ADI BF533. I had followed the schematics provided by ADI, in which construct the JTAG header from BF533 (EMU, TDO, TDI, TRST and TCK pins) using two ADG774ABRQ. However, I failed to connect my board to the USB ICE emulator, an error code 0x80048008 occurs. Did anyone try the ADI JTAG header connection bef...

Can I connect WIGGLER cable for JTAG interface to BLACKFIN533 stamp board? If yes,then; In application note of ADSP Blackfin (DOC....

Can I connect WIGGLER cable for JTAG interface to BLACKFIN533 stamp board? If yes,then; In application note of ADSP Blackfin (DOC. name-EE68)they are showing out of 14 pins available in JTAG port for the board , one pin (pin no.- 2)is connected to (Emulation Output) EMU~.So if I use WIGGLER cable as a JTAG connector then ; 1)What pin of WIGGLER cable should I connect with the PIN NO...

Selling a JTAG emulator. It is an Analog Devices Summit ICE PCI JTAG emulator. This is an excellent opportunity to enjoy the...

Selling a JTAG emulator. It is an Analog Devices Summit ICE PCI JTAG emulator. This is an excellent opportunity to enjoy the benefits of a JTAG based development environment without the high cost of buying new ($4000 + tax). Perfect condition! In the original antis

HI All!!!!! There are 3 SHARC 21062 processors in a single board, all in the master mode. How the JTAG port of these 3...

HI All!!!!! There are 3 SHARC 21062 processors in a single board, all in the master mode. How the JTAG port of these 3 SHARCs are to be brought out? Can these 3 SHARCs (All in master mode) be connected in DAISY chain mode and hence connected to only one JTAG or 3 JTAGs

Hello, Do someone know something about the private instructions and protocol for the printf() and scanf() of JTAG port? ...

Hello, Do someone know something about the private instructions and protocol for the printf() and scanf() of JTAG port? Because I'm designing a system in which I use the JTAG TAP of the ADSP-21065L to do printf() and scanf() to an LCD display and a keyboard. So, I

Hi, We would like to announce a new, low cost JTAG debugger for SHARC 2106x chips. It includes an assembler, linker and...

Hi, We would like to announce a new, low cost JTAG debugger for SHARC 2106x chips. It includes an assembler, linker and hardware debugger with no time or memory limits. It works on SHARC EZKIT boards and those with a similar JTAG port. It costs $350 and runs on Linux. For more

Hi I earlier had a ADSP21065L board with a summit ICE JTAG emulator pod.Now,I have changed my application on Blackfin...

Hi I earlier had a ADSP21065L board with a summit ICE JTAG emulator pod.Now,I have changed my application on Blackfin 533(BF533).My question is whether I could use the same emulator pod for the BF533 eval board.I tried but had no success.In JTAG CONFIGURATOR I looked in t

Hi all Iam using BF561 processor in my board Thru VDSP configurator i can able to configure the BF561 and continuous scan test is...

Hi all Iam using BF561 processor in my board Thru VDSP configurator i can able to configure the BF561 and continuous scan test is passed When i create the session in VDSP environment for BF561 its reporting JTAG not detected ... what might be the problem(becaz its detecting thru configurator !!) I followed EE68.pdf engineering note for BF jtag connectivity..... Thanks Explore...

Hi, I've installed the JTAG tools under linux and see that the byteblaster cable is one of the options for JTAG cables. I have one of...

Hi, I've installed the JTAG tools under linux and see that the byteblaster cable is one of the options for JTAG cables. I have one of these cables but there is no TRST' signal (JTAG reset) on the byteblaster cable. What should I do with the Blackfin's TRST' pin if using this cable? cheers, Jamie

Hello, There is a wonderful open-source JTAG tools available in sourceforge.net. It supports a variety of processors and also CFI complaint...

Hello, There is a wonderful open-source JTAG tools available in sourceforge.net. It supports a variety of processors and also CFI complaint flashes. Please go through the site to know more info. http://openwince.sourceforge.net/jtag/ We have added support for ADSP 21065L (MBGA) processor with AMD 512x8 flash. We have tried this new processor support in a Linux platform and which is work...

Hai, I have designed a Custom board with BF561 EZ-KIT as the reference design in which i have made certain changes to suit my...

Hai, I have designed a Custom board with BF561 EZ-KIT as the reference design in which i have made certain changes to suit my application. I've changed the Flash IC to MD8832-D1G-V18-X-P(M-systems) instead of M29W640D(ST microelectronics) present in Ezkit lite board. JTAG connector is connected with BF561 the details of which is given below JTAG ...

Hi, I am doing my project on BLACKFIN533.I have decided to use blackfin533 stamp board as devoleping platform & Eclipse as IDE. But i am in...

Hi, I am doing my project on BLACKFIN533.I have decided to use blackfin533 stamp board as devoleping platform & Eclipse as IDE. But i am in confusion that; 1)can I use Wiggler cable as JTAG cable for debugging the board? If yes, then; On the board there is 14 pin connector is provided for JTAG debugging.Out of which pin no.-2 of connector is connected to EMU~ pin of Blackfin.In applic...

Hi, Did a search on the dsp site, and couldn't find an article that matched my issue specifically. I have an in house designed board with...

Hi, Did a search on the dsp site, and couldn't find an article that matched my issue specifically. I have an in house designed board with a 21065L and the JTAG connector made available. Similar to the eval board. On the 21065L, we have connected a RT49LV4096A flash. We may even go up in size, or another one, but the HW interconnect between the 21065L

I wrote a small code in adsp2191 and that code is building properly in simulator. If i use emulator to connect to the target through JTAG...

I wrote a small code in adsp2191 and that code is building properly in simulator. If i use emulator to connect to the target through JTAG CONNECTOR,the code build message will comes and immediatly in the output window i am receiving the following ERROR  message,            

hi friends, iam using ADSP 2191 ICE. Iam facing some problems while using ADSP2191 Emulator. 1)if i open ADSP 2191 in emulator...

hi friends, iam using ADSP 2191 ICE. Iam facing some problems while using ADSP2191 Emulator. 1)if i open ADSP 2191 in emulator mode,after connecting JTAG to target board it shows the error 0x8000 4005 from this mode of selection,i can't enter into emulatormode. for entering into emulator mode,first i should enter into simulato

Hi. In the ADSP-21262 datasheet (Rev B) is it stated that the TCK line (used for JTAG port) "must be asserted (pulsed low) after power-up or...

Hi. In the ADSP-21262 datasheet (Rev B) is it stated that the TCK line (used for JTAG port) "must be asserted (pulsed low) after power-up or held low for proper operation of the ADSP-21262". However, in the ADSP-21262 EZ-KIT LITE schematic diagram it is pulled- up to mantain a high when you just run the DSP without JTAG intervention. Of course the TRST* must be held down after power-up bu...

I have designed a custom board with ADSP21262 processor. The board has a JTAG header. The ICE test passes correctly. But when I try to open the...

I have designed a custom board with ADSP21262 processor. The board has a JTAG header. The ICE test passes correctly. But when I try to open the session, it shows an erroe message. Please help me to solve out the problem..

Hi, Anyone has an example on using of jtag for data communication ? Thanks

Hi, Anyone has an example on using of jtag for data communication ? Thanks