I just went from a 5402 to a 5416 because the 5416 has more on chip RAM. I set the MP/MC=1 and OVLY=1. If my .text fits below...

I just went from a 5402 to a 5416 because the 5416 has more on chip RAM. I set the MP/MC=1 and OVLY=1. If my .text fits below 0x4000, everything is fine. If .text grows so that some is below 0x4000 and some is above 0x4000 (but below 0x5000) I keep getting runtime errors

Hello All I am working on TMS C 5416 kit. I have communicated DSP 5416(Texas Instruments) with Windows XP OS through usb...

Hello All I am working on TMS C 5416 kit. I have communicated DSP 5416(Texas Instruments) with Windows XP OS through usb interface using IC CY7C68001(EZ USB SX2) of Cypress Semiconductor coorperation. Now I want to operate this kit on Linux operating system while using the same usb interface. The Linux OS is not communicating with my kit .What should I do ? what might be...

I've just received my new 5416 dsk and am a little annoyed with the lack of documentation compared to the 5402. I have a question...

I've just received my new 5416 dsk and am a little annoyed with the lack of documentation compared to the 5402. I have a question that one of you might be able to answer: Is the tmx320 on the 5416 another dsp used exclusively for the usb to jtag interface? I mean there is no d

Hi, I've been having a terrible time just trying to program a McBSP to produce any output on any line (I'm attempting to...

Hi, I've been having a terrible time just trying to program a McBSP to produce any output on any line (I'm attempting to interface a 5416 with a TL320AD77 via a McBSP in SPI Master mode). It must be something very obvious... #define ADC_BSP hMcbsp1 MCBSP_st

Hi I create a code to TMS320VC5416. This code function very well, but I want to use the kit operating stand-alone. How can I write the code on...

Hi I create a code to TMS320VC5416. This code function very well, but I want to use the kit operating stand-alone. How can I write the code on the memory of the 5416? I saw some instructions about boot loader. This instructions mention a program called hex conversion, but I don't know where is this program. Please, help! Hugs Marcelo Check Out Industry's First Single-Chip, Multi-Form...

Hi All, I ran some application on the 5402, which runs with tight timing (80% processor usage). The application depends on...

Hi All, I ran some application on the 5402, which runs with tight timing (80% processor usage). The application depends on on-chip RAM only in both processors. Then I migrated to 5416. I did it the "stupid way": Just took the code bundle, made som

Hi, If anyone needs 5416 DSP Starter Kit, I can sell it for half of its price, I no longer need it. Contact *m if interested...

Hi, If anyone needs 5416 DSP Starter Kit, I can sell it for half of its price, I no longer need it. Contact *m if interested (replacing c*m->com) Anton

Hi, I am torn in between buying the 5402 or the 5416 DSK. The 5402 has an extra UART port, where as the 5416 talks over the...

Hi, I am torn in between buying the 5402 or the 5416 DSK. The 5402 has an extra UART port, where as the 5416 talks over the USB. How stable are the windows drivers for these platforms and is there a time limit to the tools provided? Larry Vanco

Hi, I've been trying to figure out if whether or not it is possible for me to implement an I2C bus between the PIC...

Hi, I've been trying to figure out if whether or not it is possible for me to implement an I2C bus between the PIC microcontroller and the 5416 DSK. I found some documentation available at TI about implementing it for the 54xx line of DSPs, but not specifically for DSKs

Is it possible to connect to peripheral units via the external connector on the 5416 development platform? Does anyone here...

Is it possible to connect to peripheral units via the external connector on the 5416 development platform? Does anyone here have a link to the schematic?

Hello all I am newbie in TMS320c5416 DSP and did not have experience.i would like to use ADM8696-analog device's microprocessor...

Hello all I am newbie in TMS320c5416 DSP and did not have experience.i would like to use ADM8696-analog device's microprocessor supervisory circuit and ADM3485E as a RS-485 transmiter . how can i use them with 5416?is there any recommendation? tnx 4 ur help

I am trying to do a loopback program (get data in, and send it out without any processing) on a 5416 DSK. I am using the on board ...

I am trying to do a loopback program (get data in, and send it out without any processing) on a 5416 DSK. I am using the on board PCM3002 codec and it is configured for 16-bit data transfer. I also have McBSP2 configured for 16-bit receive/transfer. The following are the register values for McBSP2 and PCM3002 codec, McBSP2 registers:

Dear all I use dsp 5416 and ads 8344 and for that I use documentation slaa 160. But why my program is not working, do anyone has try that...

Dear all I use dsp 5416 and ads 8344 and for that I use documentation slaa 160. But why my program is not working, do anyone has try that documentation? or how can I contact the author of slaa 160? thanks regard daniel

hi where do you recommend to start programming 5416 in CCS with a home made programmer thanks in...

hi where do you recommend to start programming 5416 in CCS with a home made programmer thanks in advance --------------------------------- Ahhh...imagining that irresistible "new car" smell? Check outnew cars at Yahoo! Autos.

> > hi, > I am student working on SPECTRUM DIGITAL dsk 5416. I want to take > input signal using pcm_3002 codec and then send it to...

> > hi, > I am student working on SPECTRUM DIGITAL dsk 5416. I want to take > input signal using pcm_3002 codec and then send it to speakers.This > kit uses a USB port.Does anyone know how to go about this ? > Thanks in advance , > sandy > > Hello, i also need the same info... I'm also working with the same Kit... If u r well versed in C n u ve "Code Composer Studio"

Hi Here is me again... I create a code for 5416 using Code Composer. I need to use a output to activate a relay, but the audio...

Hi Here is me again... I create a code for 5416 using Code Composer. I need to use a output to activate a relay, but the audio outputs(line-out and speaker out) are in use. I try to use the Peripheral Expansion Connector, but I don't know how to set an output, like the pin 21 for example. How can I do this? Please, help! Hugs Marcelo Check Out Industry's First Single-Chip, Multi...

Hi, I am trying to connect 2 memories each having a size of 2M x 16bits to 5416 using its memory interface. In the datasheet of 5416, it says...

Hi, I am trying to connect 2 memories each having a size of 2M x 16bits to 5416 using its memory interface. In the datasheet of 5416, it says data memory is upto 64K. So, should I use program memory space to access 2 memories? Or what can be the possible solution? Is program memory space writable?Thanks for help

hi all, thanks for the support given so far to me, At present i am doing a project on DSK5416, project is to implement LPC coder on DSK...

hi all, thanks for the support given so far to me, At present i am doing a project on DSK5416, project is to implement LPC coder on DSK 5416. DSK5416 consists PCM3002E codec, this is interfaced through CPLD on board. This CPLD is interfaced in I/O space of the 5416 DSP chip. my doubt is accessing this I/O space in high level language. i have attache a screen shot which spectrum fellow h...

Hello, I´m doing a migration from 5410A to 5416 and I´m having problems when returning from interrupt service rutines. I don´t build the...

Hello, I´m doing a migration from 5410A to 5416 and I´m having problems when returning from interrupt service rutines. I don´t build the project with the -mf option (i´m using near calls as default) because there are several vocoder funtions that we don´t want to change so I want to keep them in the same page and call them as near. For the rest of the program that is in another memory ...

Hello All I am working on TMS C 5416 kit. I have communicated DSP 5416(Texas Instruments) with Windows XP OS through usb...

Hello All I am working on TMS C 5416 kit. I have communicated DSP 5416(Texas Instruments) with Windows XP OS through usb interface using IC CY7C68001(EZ USB SX2) of Cypress Semiconductor coorperation. Now I want to operate this kit on Linux operating system while using the same usb interface. The Linux OS is not communicating with my kit .What should I do ? what might be the...