I run a program in CCS ver 2.1. I would like to watch a few vriables. But I only can look at the variables when I halt the program. When...

I run a program in CCS ver 2.1. I would like to watch a few vriables. But I only can look at the variables when I halt the program. When the program runs, the variable value is not updated. Is there any way I can watch the variables (being updated) during the program running? Thanks Jin

Hi everyone! Is there any downloadable trial version for the c5000 and the c2000 family? (ccs 3.0) I heard about the ccs3.0 for c6000...

Hi everyone! Is there any downloadable trial version for the c5000 and the c2000 family? (ccs 3.0) I heard about the ccs3.0 for c6000 DSP's, but i need it for these two other families. And i tried the 2.2.

I try to run FFT software test bench(dowm load from TI web site) on the eZdsp2407. I noticed the ccs I have is version 2 (it comes with ...

I try to run FFT software test bench(dowm load from TI web site) on the eZdsp2407. I noticed the ccs I have is version 2 (it comes with eZdsp, But the document of software test bench claimed is needed version 4.2? Where I can get this version 4.2? Thank you

Sounds like the code you look at in CCS is not what is built and loaded. _____ From: code-comp@code......

Sounds like the code you look at in CCS is not what is built and loaded. _____ From: code-comp@code... [mailto:code-comp@code...] On Behalf Of teng0422 Sent: Tuesday, May 31, 2005 5:54 PM To: code-comp@code... Subject: [code-comp] Breakpoints won't stop in source codes? I built my .out file with a buil

Hello, I've been working on the 5416 and have recently started using a jtag emulator on it (although the following problem appears when...

Hello, I've been working on the 5416 and have recently started using a jtag emulator on it (although the following problem appears when I'm using the normal simulator as well). I'm trying to step through some code in CC that wasn't written by me (but I know it works) and it is normally run on a DSK. I have a build version whi

hello everybody, i am a newcomer to dsp i wanted to learn how to use dsp/bios configuration tool fro the 2812 i wanted to know if there...

hello everybody, i am a newcomer to dsp i wanted to learn how to use dsp/bios configuration tool fro the 2812 i wanted to know if there are any manuals or books for me learn about dsp/bios whenever i try to make a dsp/bios configuration from scratch(not the one which comes as a part of ccs tutorial) i end up getting many errors how can i learn to m

When trying to load the program (in Microprocessor mode) I got the following message "Load Failed. A section of your program fails into a...

When trying to load the program (in Microprocessor mode) I got the following message "Load Failed. A section of your program fails into a memory region that is not writable. Check your linker configuration and/or memory map." I've changed nothing, my code is the same as before and it has been working fine until now. Can someone help me ? Hardware : eZdsp

Yes, you can do what you want. Basically, in the GP?MUX register (? = A,B,D,...) setting a bit to "0", configures it for GPIO,...

Yes, you can do what you want. Basically, in the GP?MUX register (? = A,B,D,...) setting a bit to "0", configures it for GPIO, settting it to "1", configures it for its internal peripheral function (SPI, CAN, etc.) Now, the GP?DIR registers are used to set the direction. 1=output, 0=input. Take a look at one of my fu

Hello all, Can anybody guide me from where I can buy the Spectrum Digital TI DSP tools such XDS510PP emulator, CCS etc..please. I am...

Hello all, Can anybody guide me from where I can buy the Spectrum Digital TI DSP tools such XDS510PP emulator, CCS etc..please. I am located at Bangalore, India. Thanks & Best Regards Anand

hi, I'm working on the simulator c54x(ccs v2). In my c code i'm inputing two *.dat files through probe points and also taking the output...

hi, I'm working on the simulator c54x(ccs v2). In my c code i'm inputing two *.dat files through probe points and also taking the output in two *.dat files . I'v converted the wav file to dat file through c code and store them in teh project folder and included the ccs header into the dat files. when i'm running code, i get this message op