Jeff, If you are having problems with noise on long JTAG chains, try to buffer the JTAG lines. I have seen boards with 16 C6000...

Jeff, If you are having problems with noise on long JTAG chains, try to buffer the JTAG lines. I have seen boards with 16 C6000 DSPs on a single chain that worked just fine. I guess the trick may be in keeping the JTAG lines well laid out on the PCB. If it is too

Hi, Is there a way to use a custum JTAG interface with CCS and the C2000 series of DSP's from ti. Or is there a way to build a JTAG interface...

Hi, Is there a way to use a custum JTAG interface with CCS and the C2000 series of DSP's from ti. Or is there a way to build a JTAG interface that works with CCS like for other devices like the Altera, Xilinx FPGA's and the MSP430 devices where the shematics are made public. If not which emulator do you recommend to buy? Any Help is appreciated. Best regards, Janko Horvat

All- Is there a way to independently test a Spectrum Digital XDS510PP emulator and JTAG scan chain without using SDConfig? Our lab servers...

All- Is there a way to independently test a Spectrum Digital XDS510PP emulator and JTAG scan chain without using SDConfig? Our lab servers do not have motherboard parallel ports. Adding parallel port PCI/PCIe cards fails with SDConfig because Spectrum Digital uses "direct I/O" access to legacy parallel port addresses (e.g. 0x0378, 0x0278, etc), and they have not fixed this over the years...

Hi, Am using CCS v3.1 platinum edition, to work on OMAP 1510 innovator kit. The Sdopts.cfg displays the following on emu-check: ** Emulator...

Hi, Am using CCS v3.1 platinum edition, to work on OMAP 1510 innovator kit. The Sdopts.cfg displays the following on emu-check: ** Emulator Test ** $$ EmuProductName=XDS510PP_PLUS $$ EmuPortAddr=0x378 $$ EmuPortMode=SPP8 $$ ProductId=10 $$ ProductVersion=02 ** Emulator Scan Test -- Found JTAG IR length of 50 -- Found 3 JTAG device(s) in the scan chain ...

Hello All, We are using XDS510 USB JTAG for OMAP platform,when I run SDCONFIG for emulation verification. Following are ...

Hello All, We are using XDS510 USB JTAG for OMAP platform,when I run SDCONFIG for emulation verification. Following are details displayed when we click on emulator test button. EmuProductName=XDS510USB EmuPortAddr=0x510 EmuPortMode=USB Pro

Hi all, is there someone who have expieriences with using the XDS5100PP JTAG with other devices than TI DSP? In my case I...

Hi all, is there someone who have expieriences with using the XDS5100PP JTAG with other devices than TI DSP? In my case I search for a possibility to connect the XDS510PP emulator to a Motorola DSP. with regards tom

Gagan- > I guess better put the TI device as first > CPU in the boundary scan chain. This might help. I > only run homogenous...

Gagan- > I guess better put the TI device as first > CPU in the boundary scan chain. This might help. I > only run homogenous mix of 8 TI DSPs in single chain. > But havn't try on the hetrogenous mix of other CPUs > Other thing is to slow the JTAG clock fr

The JTAG port is used both for debugging software in development and for boundary scan hardware test in production. Most of the PLD...

The JTAG port is used both for debugging software in development and for boundary scan hardware test in production. Most of the PLD vendors provide support in their programming software for other devices in the scan chain. But I have received mixed advice on putting TI DSPs in a scan chain

Hi Rick, You can have a look on www.mlabsys.com/miragex.htm Good luck, Jan -----Original Message----- From: Rick...

Hi Rick, You can have a look on www.mlabsys.com/miragex.htm Good luck, Jan -----Original Message----- From: Rick Collins [mailto:] Sent: zondag 3 februari 2002 17:46 To: Subject: [code-comp] Using XDS510 for JTAG boundary scan testing

I am new to designing with TI DSPs and am looking at purchasing an emulator. Does anyone have any experience using the new...

I am new to designing with TI DSPs and am looking at purchasing an emulator. Does anyone have any experience using the new Blackhawk USB-JTAG emulator? It seems like a better way to go than the ISA card and parallel port based emulators. Appreciate hearing from yo

Hi all We developped a board with four C6201 in the JTAG chain and want to debug them with the XDS510 Emulator and Code...

Hi all We developped a board with four C6201 in the JTAG chain and want to debug them with the XDS510 Emulator and Code Composer Studio Debug Tools 1.20. The DSPs are the only devices in the JTAG chain. The Emulator is connected as in the TI application note SPRA439, fi

Hello all,, has somebody some documentation about how Code Composer uses JTAG? Has somebody any info about the source code of...

Hello all,, has somebody some documentation about how Code Composer uses JTAG? Has somebody any info about the source code of CC drivers for TI C6701? Does anybody worked on porting Code Composer to a custom DSP architecture? Any info would be appreciated.

Alright, now that I've got the ability to compile from the command line, I'd like to flash the ezDSP2808 over JTAG from the command line. Web...

Alright, now that I've got the ability to compile from the command line, I'd like to flash the ezDSP2808 over JTAG from the command line. Web searches have revealed tiny tidbits here and there, but not much. I'm worried that I may end up having to try to build a program to do this. _____________________________________

I've tried a variety of things with flashburn to write to my ezDSP 2808 via jtag via the blackhawk usb2000 controller. BlackHawk provides...

I've tried a variety of things with flashburn to write to my ezDSP 2808 via jtag via the blackhawk usb2000 controller. BlackHawk provides BHFlashBurn for this purpose.. I've tried things like: @cls @rem @path %path%;c:\progra~1\Blackhawk\flashburn_v3\bin\ bhflashburn -d bhemu28x.dvr -f lf28xx.dat -p0x0 -r -e -cx30x6 c:\progra~1\blackhawk\flashburn_v3\bin\flash28xx\algorithms\2812\flasha...

Once found, the latest update from Spectrum Digital website, the 3.3 version already shows the existence of a Factory Board for our Mistral OMAP...

Once found, the latest update from Spectrum Digital website, the 3.3 version already shows the existence of a Factory Board for our Mistral OMAP 3530 EVM. As we want to connect it through the JTAG with the XDS510USB, we're trying to set everything up. The problem appears when we push Save and Quit, because an error message shows up: ERROR AUTOMATICALLY GENERATING BOARD FILE. AN INVALID ROUTER FAM...

Does it exist any version of Code Compser or even currently v3.3 which runs in OMAP 35.x Evaluation Module? We're dealing with the latest version...

Does it exist any version of Code Compser or even currently v3.3 which runs in OMAP 35.x Evaluation Module? We're dealing with the latest version (CCS 3.3) but no updated, I'm afraid, so we cannot connect our CCS with the board via JTAG (XDS510USB emulator). Does someone know if exist the software?

Hi I have bought a xds510-usb2.0 jtag dsp emulator from YUHUA Elec. Co. . Does it has any technical support web site? How can I install...

Hi I have bought a xds510-usb2.0 jtag dsp emulator from YUHUA Elec. Co. . Does it has any technical support web site? How can I install it for code composer 3.3 or even 3.1? I installed previously emulators from WINTECH and Spectrum Digital, but I can't install this emulator even I tried all of *.exe files in its CD. Would you please guide me obviously? I have windows XP (sp2) and attache...

Hi to every one,,, I have Davinci-DM644x Evaluation Module and XDS510 USB Jtag and i'm using code composer CCS v3.3 under windows XP. I tested...

Hi to every one,,, I have Davinci-DM644x Evaluation Module and XDS510 USB Jtag and i'm using code composer CCS v3.3 under windows XP. I tested by using a small program to perform the binking of 8-leds, without any problem. And I loaded (.out) file successfully to the board (ARM-side). However when the power is turned OFF, and then turned ON, the blinking of leds stopped. (I could not solve t...

Hello, I am currently working on a multiple DSP application, and need to connect 2 or more eZDSP R2812 boards to my PC simultaneously. I know...

Hello, I am currently working on a multiple DSP application, and need to connect 2 or more eZDSP R2812 boards to my PC simultaneously. I know the current release of CCS does not allow you to do this directly, but does anyone know of any "indirect" methods? I know you can connect different DSPs if you use a different JTAG emulator for each one, but is there any other way? Thanks for any help ...

Hey!~guys. My project is under ccs3.1, I use xds560 PCI-JTAG emulator. The program runs pretty well, in which all the .c source file I can...

Hey!~guys. My project is under ccs3.1, I use xds560 PCI-JTAG emulator. The program runs pretty well, in which all the .c source file I can build with -o3 option. Except for one file, after I built this bad.c source file within -o2 and run, the program died (fall into endless running but it is supposed to end)~ When I halt the program and check the disassembly, it stops within the lable: ME...