Hey Gustl, i am having a problem initializing the I2C module on the C6713 DSK and i really need your help we are sending an address to a...

Hey Gustl, i am having a problem initializing the I2C module on the C6713 DSK and i really need your help we are sending an address to a camera (SLAVE) to change format settings, resolution, frame rate and so on, so we send the address and then the apprpriate data value to that register for the change I see that you have code which follows the same initialization proc, but can you please

Hello all, I am new to this group. I am designing a PCB around the C6713 DSP. I am looking at the power supply and it seems I need to supply...

Hello all, I am new to this group. I am designing a PCB around the C6713 DSP. I am looking at the power supply and it seems I need to supply two different levels DVdd (I/O) and CVdd (Core), which should ideally be 3.3 and 1.2V, respectively. Reading through the document: "Embedded Processing Guide", they suggest the use of a very complicated power supply utilising two TPS54350PWP ICs. Is ...

Hi folks, I attended the TI Developers Conference last week and picked up the C6713 DSK. This included the DSK version of CCStudio...

Hi folks, I attended the TI Developers Conference last week and picked up the C6713 DSK. This included the DSK version of CCStudio 2.21. I was told at one of the workshops that this version of CCStudio was limited in size of executables that could be produced. My question: What are the l

Hello everyone, I am trying to use my C6713 to write to an I2C EEPROM (Model:M24C02 - Addr: 0xA0 - Only device on the bus) but...

Hello everyone, I am trying to use my C6713 to write to an I2C EEPROM (Model:M24C02 - Addr: 0xA0 - Only device on the bus) but can't seem to be able to successfully perform a write cycle. While I was debugging using a Scope, I had realized that the 8th Bit of my "Device S

Hi all I want to receive 70 MHz PM+BPSK modulated signal. Video bandwidth:138 kHz Modulation index for PM: 1.2 radian Subcarrier...

Hi all I want to receive 70 MHz PM+BPSK modulated signal. Video bandwidth:138 kHz Modulation index for PM: 1.2 radian Subcarrier frequency of BPSK:65536 Hz. I have been using Matlab /Simulink and TMS320C6713 DSK. 1. I need suitable ADC daughtercard for C6713 DSK. 2. What is the sampling rate according to this spec.s? How can I calculate? I want to proof my calculation method. ...

PLEASE CAN YOU HELP ME ABOUT a C code for PWM in C6713 DSK because this is my project subject I couldnt find if you can help me I am waiting...

PLEASE CAN YOU HELP ME ABOUT a C code for PWM in C6713 DSK because this is my project subject I couldnt find if you can help me I am waiting your messages or e-mails...(TOO IMPORTANT FOR ME)!! I am a electrics & electronics engineering student... VERY URGENT!!

Hello, I bought Dr Chassaing's book in 'low price edition' version (available in Indian subcontinent at affordable rates) but it turns out...

Hello, I bought Dr Chassaing's book in 'low price edition' version (available in Indian subcontinent at affordable rates) but it turns out that it does not have the CD-ROM. Ofcourse I bought the book for learning the c6713 kit as I already know & teach DSP using Li Tan's, Ifeacher's and Proakis' book for that. So, I'd appreciate it very much if you can send me the CD rom files ...

Hello, I'm working on the C6713 DSK and when I compile my program I have the following error : [Linking...] "c:\ti\c6000\cgtools\bin\cl6x"...

Hello, I'm working on the C6713 DSK and when I compile my program I have the following error : [Linking...] "c:\ti\c6000\cgtools\bin\cl6x" -@"Debug.lkf" > > error: can't allocate .TSK_idle$stk (sz: 00000400 page: 0) in IRAM (avail: 00000314) > > error: errors in input - ./Debug/essai1.out not built Please,What does this message means? And how I can solve it? _______________

Hi I have been trying to modify one of the exercise codes given in Dr Rulp Chassaings Book 'Digital Signal Processing with the C6713 and C6416...

Hi I have been trying to modify one of the exercise codes given in Dr Rulp Chassaings Book 'Digital Signal Processing with the C6713 and C6416 DSK," Wiley, 2005. Ive attached the modified main file 'AdaptIDFIR1.c' as well as the original project.The only difference being tht ive used external input (line or mic) instead of random noise used in the original. and NLms algo is used instead of...

Hello all, I am a student who is getting to know the C6713 DSK. I got the Dr. Ralph Chassaing book entitled "Digital Signal Processing...

Hello all, I am a student who is getting to know the C6713 DSK. I got the Dr. Ralph Chassaing book entitled "Digital Signal Processing and Application with C6713 and C6412 DSK" in our university library but they don't have the enclosed CD-ROM (the one that contains the programs/files). But i am looking for the 2nd edition, Digital Signal Processing and Applications with the TMS320C6713 and T...

Dear All I am using c6713 dsk with CCS software. it's sampling frequency minimum 8KHz , max 99KHz & 256 FFT point. I want to process real signal...

Dear All I am using c6713 dsk with CCS software. it's sampling frequency minimum 8KHz , max 99KHz & 256 FFT point. I want to process real signal 0.5Hz to 10 Hz. Is it possible to process or do FFT for this frequency band ? If not, how can i do it ... Your kind help will be highly appreciated. Regards Gopal Sarkar, Kolkata _____________________________________

Wajahat- I think Joshy meant this for you. -Jeff -------- Original Message -------- Subject: Re: [c6x] Code to get output from McBSP of...

Wajahat- I think Joshy meant this for you. -Jeff -------- Original Message -------- Subject: Re: [c6x] Code to get output from McBSP of C6713 Date: Fri, 16 Feb 2007 23:10:20 ? From: "joshy jose" To: "Jeff Brower" yes you can check it i have done it, you can use the sample program available from ti site there is one particular ex

Greetings to the Community I am trying to implement a modem using 2 separate Spectrum Digital c6713 boards, one setup as a transmitter and the...

Greetings to the Community I am trying to implement a modem using 2 separate Spectrum Digital c6713 boards, one setup as a transmitter and the other as receiver. The idea is basically connecting my iPod output to the line in of transmitter, do some modulation and pulseshaping, then send it out the line out, which goes into the linein of the second dsk. The following are the parameter that I'...

Hello I am trying to implement a modem using 2 separate Spectrum Digital c6713 boards, one setup as a transmitter and the other as receiver....

Hello I am trying to implement a modem using 2 separate Spectrum Digital c6713 boards, one setup as a transmitter and the other as receiver. The idea is basically connecting my iPod output to the line in of transmitter, do some modulation and pulseshaping, then send it out the line out, which goes into the linein of the second dsk. The following are the parameter that I'm (initially) planni...

the voltage on the c6711-dx-pin was approx. 3,3v, changes to zero and then starts the data-transfer. but now on the c6713-dsk,...

the voltage on the c6711-dx-pin was approx. 3,3v, changes to zero and then starts the data-transfer. but now on the c6713-dsk, it`s always zero, but the DR-pin of the c6713-dsk`s is always 3,3v like the c6711, so when i connect these pins, the voltage is approx. 1,7v with no changing

Hi, I'm looking for some documentation what causes data memory stalls on a C6713. The only thing I found so far is spru733a. And it says...

Hi, I'm looking for some documentation what causes data memory stalls on a C6713. The only thing I found so far is spru733a. And it says only: 'A memory stall occurs when memory is not ready to respond to an access from the CPU.' I'm using combinations of STW, LDW and LDDW. I want to know which combinations are causing stalls. It would be help full to know how the simulator indicat...

Hi, I have interfaced a 12-bit ADC with C6713 DSP. How can I scale the output to see the amplitude of the output signal same as of input...

Hi, I have interfaced a 12-bit ADC with C6713 DSP. How can I scale the output to see the amplitude of the output signal same as of input signal ? For example, Amplitude = 2 Vp_p with 5KHz frequency ? I want to run ADC for 5 minutes or more and save all the sampled values in a file to examine them in Matlab ? Can you please tell me how could I do it ? Waiting for your help. BR, B...

http://faculty.tp.devry.edu/~tmack/classes/syllabus/eet350spring2006.htm Search on this page "Zipped Files for sine wave generation". It...

http://faculty.tp.devry.edu/~tmack/classes/syllabus/eet350spring2006.htm Search on this page "Zipped Files for sine wave generation". It ıncludes CD file. I hope it would be helpful to u. > > Hello, > Rulph Chassaing wrote 2 books: ?? - DSP Applications Using C and Tms320c6x Dsk ?? - Digital Signal Processing and Applications with the C6713 and C6416 DSK > The data sourc...

I'm currently having a bunch of trouble getting my C6713 to boot off of flash properly. I can program and run the blink LED example...

I'm currently having a bunch of trouble getting my C6713 to boot off of flash properly. I can program and run the blink LED example just fine. But when I try to program my code in, I can never get it to work. I've tried doing some modifications on the blink boot code, the post boot c

Hello, I have a c6713 DSK and I am trying to transfer data to a PC in real-time using Avnet's "TI DSK to USB2" board but except for EP0 and...

Hello, I have a c6713 DSK and I am trying to transfer data to a PC in real-time using Avnet's "TI DSK to USB2" board but except for EP0 and EP2(corrupts data in BULK mode) I have not been able to read/write from the other endpoints(EP{4,6,8}). Has anybody managed to get the two working? Sincerely, Todor