JTAG Problem for DM6446

Started by Nilanjan Goswami in TMS320c6x12 years ago 2 replies

Hi Folks, My organization just purchased a new DM6446 EVM from spectrum digital. They told that this board supports their old XDS510USB JTAG...

Hi Folks, My organization just purchased a new DM6446 EVM from spectrum digital. They told that this board supports their old XDS510USB JTAG which we already possess. But the MSP340 JTAG JTAG connector of the EVM does not match the JTAG connector we have of XDS510USB. So my query is: 1. Doses this board at all supports the XDS510USB JTAG? 2. As you already know JTAG is a very costl...


CCS Bring up through JTAG for C6415

Started by gururajb2 in TMS320c6x17 years ago 2 replies

hi all, I am facing problem in bringing up CCS through JTAG for C6415 .Since all conections to JTAG header is less than 6 inchs i...

hi all, I am facing problem in bringing up CCS through JTAG for C6415 .Since all conections to JTAG header is less than 6 inchs i am not using any signal buffering. Pls inform any other precautions are to be taken for JTAG. Thanks in advance. -- gururaj


TMS of JTAG

Started by yang...@163.com in TMS320c6x12 years ago 1 reply

hi all, I am facing problem in bringing up CCS through JTAG for C6416 . When power on,TMS is about 1.6v,so we cannot bring up CCS through JTAG...

hi all, I am facing problem in bringing up CCS through JTAG for C6416 . When power on,TMS is about 1.6v,so we cannot bring up CCS through JTAG emulator. Does somebody know what is the reason? Thanks.


60 Pin JTAG Header

Started by shad...@yahoo.com in TMS320c6x12 years ago 8 replies

Hi, all. I have a problem with a JTAG header. There is a 60 pin JTAG header in DSK for TMS320C6416T (Spectrum Digital). I've checked...

Hi, all. I have a problem with a JTAG header. There is a 60 pin JTAG header in DSK for TMS320C6416T (Spectrum Digital). I've checked whether the 60 pin header works properly using XDS560R JTAG Emulator (14 pin) and 14 pin to 60 pin connector. However, when I ran the Code Composer Studio IDE 3.3, an error message showed up as follow: ----------------------------------------- Error c...


Question on JTAG Emulator.

Started by Anonymous in TMS320c6x18 years ago 5 replies

Hello all. I have a simple question on JTAG Emulator. To emulate means to imitate. In the case of EVM or DSK, what components are...

Hello all. I have a simple question on JTAG Emulator. To emulate means to imitate. In the case of EVM or DSK, what components are the JTAG Emulator trying to emulate? What is the purpose of having JTAG Emulator? Any comments/explanations/advices are welcome. Thank


JTAG Emulation via PCI

Started by raja nayaka in TMS320c6x17 years ago 2 replies

hi friends May i know what is meant by JTAG emulation via PCI?, how to achieve it?, what interface i need, to make...

hi friends May i know what is meant by JTAG emulation via PCI?, how to achieve it?, what interface i need, to make communication between JTAG and CCS , other than using XDAS510.... please give me your suggetion thanking you rjnayaka


[Fwd: Re: can't connect to target after flashburn]

Started by Jeff Brower in TMS320c6x16 years ago 1 reply

Mike- What can programming Flash do to hold up JTAG on the DSK board? It must be DSK board specific, because normally -- as...

Mike- What can programming Flash do to hold up JTAG on the DSK board? It must be DSK board specific, because normally -- as long as C67xx reset is not held and JTAG signals are still connected and healthy - JTAG should be enabled. I suppose the CCS driver is


xds510 jtag emulator

Started by Yasser Attarizzi in TMS320c6x14 years ago 12 replies

hi i design a board with c6201 and want to load the program with xds510 jtag emulator what is the minimum requirement for jtag emulator...

hi i design a board with c6201 and want to load the program with xds510 jtag emulator what is the minimum requirement for jtag emulator to detect the IC? I mean which pins have to be pulled up and what is nesessary for example oscilator or reset pullup? thanks yasser ______________________________________________________________


TI JTAG signal integrity issue

Started by Jeff Brower in TMS320c6x6 years ago 8 replies

All- I'm posting this question here, the global knowledge source for TI JTAG related issues :-) I have a batch of C5510A modules that are...

All- I'm posting this question here, the global knowledge source for TI JTAG related issues :-) I have a batch of C5510A modules that are showing inconsistent JTAG scan test results. Out of 6, 3 are passing, two with buffered TCK and RTCK, and 1 without (without = bypass the buffer using zero-ohm Rs). The failing modules also are configured both ways. Due to this variation, I'm concerned...


Install JTAG??

Started by dibyendu mondal in TMS320c6x15 years ago 1 reply

Hi all Today I get JTAG xds510pp_plus but I have find a problem to install it. I have the system: ______________ ...

Hi all Today I get JTAG xds510pp_plus but I have find a problem to install it. I have the system: ______________ |C6x DSP board |<----- Printer port ----->PC and the new one: ______________ |C6x DSP board | (<---) JTAG In


JTAG and CCS

Started by mayongfeng00 in TMS320c6x17 years ago 1 reply

Hi,everyone! I am debugging a board with 4 DSPs that are in a JTAG loop. One of the 4 DSPs is HOST which can access the other 3...

Hi,everyone! I am debugging a board with 4 DSPs that are in a JTAG loop. One of the 4 DSPs is HOST which can access the other 3 slaves through the HPI. But one of the slaves doesn't work well,ie, can't get into the CCS if it is in the JTAG loop. Can anyone give me any hints?


Connecting DM648 with XDS510PP+

Started by ketan deshpande in TMS320c6x12 years ago 1 reply

Hello Everybody, We have the new EVMDM648 and are trying to connect the JTAG to it. When we try in SDConfig then we get the following...

Hello Everybody, We have the new EVMDM648 and are trying to connect the JTAG to it. When we try in SDConfig then we get the following messages ** Emulator Test ** $$ EmuProductName=XDS510PP_PLUS $$ EmuPortAddr=0x378 $$ EmuPortMode=SPP8 $$ ProductId=10 $$ ProductVersion=02 ** Emulator Scan Test -- Found JTAG IR length of 6 -- Found 1 JTAG device(s...


Re: XDS510PP PLUS JTAG and usb converter

Started by csl...@danfoss.com in TMS320c6x12 years ago 1 reply

Hi Damien, I have the exact same issue/problem as the one you describe below. I wish to use my XDS510PP-plus JTAG emulator on a PC that has no...

Hi Damien, I have the exact same issue/problem as the one you describe below. I wish to use my XDS510PP-plus JTAG emulator on a PC that has no parallel port. Therefore I am curious to know if you managed to find a way how to do that. Best regards, Christian Dear DSP experts, > > We own a XDS510PP PLUS JTAG emulator, which works on a parallel port. > We would like to use it with a laptop,


XDS560 vs XDS510 JTAG

Started by Nilanjan Goswami in TMS320c6x12 years ago 1 reply

Hi Folks, Thank you all very much for resolving the XDS510 USB JTAG connector problem DaVinci EVM. I have searched for the fast JTAG in...

Hi Folks, Thank you all very much for resolving the XDS510 USB JTAG connector problem DaVinci EVM. I have searched for the fast JTAG in the internet, but I am really perplexed. I found two different variations of the hardware (XDS560), USB based and PCI based from different vendors. 1. Can in anybody tell me why XDS560 is faster than XDS510? 2. Which one should I purchase USB based...


CCS and JTAG help

Started by T a h i r in TMS320c6x13 years ago 10 replies

Hi, I am trying to connect my custom board using CCS3.0 tunning version and external jtag emulator but found an error that "Can't initialize...

Hi, I am trying to connect my custom board using CCS3.0 tunning version and external jtag emulator but found an error that "Can't initialize the target CPU". My configuration are: -Custom board, C6414, 400MHz, -Win2k platform. -Spectrum digital emulator XDS510PP plus emulator. SDCconfig utility, shipped with the emulator can verify, test and complete the JTAG scan path without any e...


Programming flash with JTAG and C6713

Started by z_11...@yahoo.com in TMS320c6x12 years ago 2 replies

Dear all I have a design with C6713. I want to program flash with c6713 and JTAG. Can I use JTAG for first boot configuration? How? How can I...

Dear all I have a design with C6713. I want to program flash with c6713 and JTAG. Can I use JTAG for first boot configuration? How? How can I program flash in this condition (by JTAG) before any initializing or configuration on c6713? If C6713 need special configuration, please guide me. Is it possible to changing boot mode to EMIF boot and copy my data from flash then run program? Really a...


XDS510PP PLUS JTAG and usb converter

Started by in TMS320c6x14 years ago 1 reply

Dear DSP experts, We own a XDS510PP PLUS JTAG emulator, which works on a parallel port. We would like to use it with a laptop, but as you know...

Dear DSP experts, We own a XDS510PP PLUS JTAG emulator, which works on a parallel port. We would like to use it with a laptop, but as you know most of the laptops are now supplied without parallel port! Therefore, I am interested to know if some of you already used the XDS510PP Jtag with a USB to parallel port converter, and if you encountered any differences or limitations compared to ...


TCI6488 JTAG emulation conection problem.

Started by jeev...@yahoo.co.in in TMS320c6x10 years ago 1 reply

Hi All, Our board(Product) has TCI6488 processor. We have a blackhawk JTAG emulator. we have installed the CCS V3.3 with SR12 patch and...

Hi All, Our board(Product) has TCI6488 processor. We have a blackhawk JTAG emulator. we have installed the CCS V3.3 with SR12 patch and installed the JTAG driver. While we are trying to open the emulator debugger and tried to connect to the target it shows the below error message. Error connecting to the target: Error 0x80002240/-183 Fatal Error during: Initialization, OCS, Control, Thi...


using an old Blackhawk USB560 JTAG Emulator with a newer EVM6446 board

Started by Sara Grassi in TMS320c6x10 years ago 3 replies

Hello, I have a Blackhawk USB560 JTAG Emulator (BH-USB-560M-OE) , which we bought in December 2005 for a past project. Now I would like to...

Hello, I have a Blackhawk USB560 JTAG Emulator (BH-USB-560M-OE) , which we bought in December 2005 for a past project. Now I would like to use it with our EVM6446 board rev. F, which we bought recently, and Code Composer Studio Platinum version 4.. I understand that I will have to buy a "TMDSADP1420 - Adaptive Clocking JTAG Emulator Adapters". But apart from that, do we have a chan...


jtag xds510 usb2.0

Started by nidhameddine in TMS320c6x11 years ago 1 reply

hi for all i have a jtag xds 510 usb2.0 but the cd of install is endamaged. please i need this driver. thinks

hi for all i have a jtag xds 510 usb2.0 but the cd of install is endamaged. please i need this driver. thinks