DSPRelated.com

emulator advice

Started by rich...@yahoo.com in TMS320c6x15 years ago 1 reply

Hi We have developed a product based around the c6711 processor. We would like to buy an emulator such as the XDS560 so we can debug the...

Hi We have developed a product based around the c6711 processor. We would like to buy an emulator such as the XDS560 so we can debug the product but we know that these are very expensive. A low to medium range product would be acceptable also. Does anyone know of a cheaper emulator that we can use instead? Or does anyone have a suitable emulator for rent or sale? thanks for your he...


Emulator connection

Started by rohi...@gmail.com in TMS320c6x14 years ago 5 replies

Hi I am trying to get a good emulator connection to my dsp c6713 on my custom board . But i can only connect few times after many tries . The...

Hi I am trying to get a good emulator connection to my dsp c6713 on my custom board . But i can only connect few times after many tries . The emulator I am using is the xds510 by digital spectrum . I checked all connection for the emulator and seems fine . Can you suggest methods to solve the problem . Secondly , I have a buck converter that converts an input 5V to 3.3V , but when i sw...


Emulator Selection - Help needed

Started by kumar_kt in TMS320c6x18 years ago 4 replies

Hi All, We have been using 510 emulator till now. I am planning to buy a XDS560 emulator. I am working in DM642 EVM board. I went...

Hi All, We have been using 510 emulator till now. I am planning to buy a XDS560 emulator. I am working in DM642 EVM board. I went through several websites and noticed several emulator models. I am in a dilemma to choose the right model. The following are the criteria for selection, questions I had in mind and the models that I went through;


Emulator Cleanup

Started by swapnali patil in TMS320c6x17 years ago 7 replies

Hello All, We have PCI Emulator in our company. As it is a PIC emulator it is inside CPU, and that CPU is not opened ,cleaned...

Hello All, We have PCI Emulator in our company. As it is a PIC emulator it is inside CPU, and that CPU is not opened ,cleaned since last 2.5 years. Till now it must have got lotz of dust inside. Will this create any problem in future. If I want to clean the emulator, what kind of precautionary steps should be followed. Thanks and Regards -swapnali ...


problem with usb emulator

Started by prabhu Abbigeri in TMS320c6x17 years ago 1 reply

hello everybody, ours is an audio related product which contains 3 c672x dsps connected in daisy chain. we are debugging with engineering...

hello everybody, ours is an audio related product which contains 3 c672x dsps connected in daisy chain. we are debugging with engineering prototype. am facing a strange problem.c672x dsp works fine(load and run) with PP+ emulator. but doesnt work with usb emulator. 1. Found that the dsp board gets connected and works well with PP+ emulator. with with usb emulator, even we ...


XDS510 USB Hardware Problem

Started by pan....@zte.com.cn in TMS320c6x18 years ago 1 reply

I am developing a DM642-based target board using a XDS510 USB JTAG emulator. Yesterday I found that the emulator can't connect my target board....

I am developing a DM642-based target board using a XDS510 USB JTAG emulator. Yesterday I found that the emulator can't connect my target board. The error log of the SDConfig is listed below: ** Checking emulator/eZdsp scan connection ** Emulator Test ** $$ EmuProductName=XDS510USB $$ EmuPortAddr=0x510 $$ EmuPortMode=USB $$ ProductId=510 $$ ProductVersion=84 ** Emulator Scan Test -


Question on JTAG Emulator.

Started by Anonymous in TMS320c6x22 years ago 5 replies

Hello all. I have a simple question on JTAG Emulator. To emulate means to imitate. In the case of EVM or DSK, what components are...

Hello all. I have a simple question on JTAG Emulator. To emulate means to imitate. In the case of EVM or DSK, what components are the JTAG Emulator trying to emulate? What is the purpose of having JTAG Emulator? Any comments/explanations/advices are welcome. Thank


Emulator for 6713

Started by gius...@libero.it in TMS320c6x18 years ago 4 replies

I need an emulator for 6713. What I want is a particular emulator which is able to show me all pins in order to test my daugther card because I'm...

I need an emulator for 6713. What I want is a particular emulator which is able to show me all pins in order to test my daugther card because I'm not sure of the particular function of each pinout. Thank you.


CCS and JTAG help

Started by T a h i r in TMS320c6x17 years ago 10 replies

Hi, I am trying to connect my custom board using CCS3.0 tunning version and external jtag emulator but found an error that "Can't initialize...

Hi, I am trying to connect my custom board using CCS3.0 tunning version and external jtag emulator but found an error that "Can't initialize the target CPU". My configuration are: -Custom board, C6414, 400MHz, -Win2k platform. -Spectrum digital emulator XDS510PP plus emulator. SDCconfig utility, shipped with the emulator can verify, test and complete the JTAG scan path without any e...


Using Parallel Debug Manager

Started by Jagadeesh Bhaskar P in TMS320c6x18 years ago 4 replies

Hi, Is it possible for me to use Parallel Debug Manger with my CCS3.1, with a c64x device accurate simulator as the target? I have seen a ...

Hi, Is it possible for me to use Parallel Debug Manger with my CCS3.1, with a c64x device accurate simulator as the target? I have seen a different setting as emulator. What is the difference of emulator from simulator and DSK? Isn't DSK and emulator basically the same? And if I have to run my target application on an emulator, will i need a real board?


Emulator not being initialised

Started by Ravi Kadam in TMS320c6x22 years ago 1 reply

Dear Group, Right now I am working on TMS3206211 and the Emulator that we are using is Spectrum Digital XDS510PP_Plus and the...

Dear Group, Right now I am working on TMS3206211 and the Emulator that we are using is Spectrum Digital XDS510PP_Plus and the port that we are using is the 0x378 set at ECP+EPP mode. But I am unable to initialize the Board through Emulator using CC Studio.


Enable port 0x510 CCS Setup

Started by edua...@ims.ind.br in TMS320c6x16 years ago 3 replies

Hi, I have got a EVMC6727 and a Spectrum Digital Emulator XDS510USB. I have installed the emulator and run the SDConfig, everything says OK....

Hi, I have got a EVMC6727 and a Spectrum Digital Emulator XDS510USB. I have installed the emulator and run the SDConfig, everything says OK. The port that it says I'm using is the 0x510. ** Emulator Test ** $$ EmuProductName=XDS510USB $$ EmuPortAddr=0x510 $$ EmuPortMode=USB $$ ProductId=510 $$ ProductVersion=84 ** Emulator Scan Test -- Found JTAG IR length of 54 -- Found...


problem using jtag with c6424 evm

Started by ahme...@yahoo.com in TMS320c6x15 years ago

Hi all,i am trying to use xds560 USB emulator with my c6424evm board, i hv installed all the drivers but still my board has not yet appeared in...

Hi all,i am trying to use xds560 USB emulator with my c6424evm board, i hv installed all the drivers but still my board has not yet appeared in ccs setup with emulator,i hv also tried xds560 c6455 emulator with my board but it works for limited number of applications(all are non bios app).so plz guide me in using xds560 USB emulator with c6424 evm _____________________________________


xds510 jtag emulator

Started by Yasser Attarizzi in TMS320c6x18 years ago 12 replies

hi i design a board with c6201 and want to load the program with xds510 jtag emulator what is the minimum requirement for jtag emulator...

hi i design a board with c6201 and want to load the program with xds510 jtag emulator what is the minimum requirement for jtag emulator to detect the IC? I mean which pins have to be pulled up and what is nesessary for example oscilator or reset pullup? thanks yasser ______________________________________________________________


Target Initialization Problems.........

Started by simha j in TMS320c6x22 years ago 1 reply

Hello all, I have ccs 2.0 and Emulator drivers from Spectrum Digital. I have connected the Emulator (XDS510PP PLUS) to my ...

Hello all, I have ccs 2.0 and Emulator drivers from Spectrum Digital. I have connected the Emulator (XDS510PP PLUS) to my own hardware board(cantains single C6211 processor) and I have configured the ccs in emulator mode. But I am encountering the follo


xds560 emulator

Started by Goh Chee Wei in TMS320c6x20 years ago 1 reply

I have recently bought a xds560 emulator. However I encounter some problem in using the board. I did not receive any installation...

I have recently bought a xds560 emulator. However I encounter some problem in using the board. I did not receive any installation disk when i bought the emulator. DO I need to install an device driver? I am running ccs ver2.1. Did anyone use this product before, need help urgen


Problems on 510usb emulator

Started by luck in TMS320c6x16 years ago 4 replies

hi all: I meet a strange problem on 510usb emulator. Environment: (1)DSP C6727B, (2)CCS v3.3 , (3)emulator: 510usb emulator.(4)...

hi all: I meet a strange problem on 510usb emulator. Environment: (1)DSP C6727B, (2)CCS v3.3 , (3)emulator: 510usb emulator.(4) program are all located in internal RAM I write a test project in ASM. After the compiling and linking, the output file can be downloaded to DSP(C6727B), and it runs well. But when I write a test project in C, after the compiling and linki...


a question about the emulator of c672x

Started by luck in TMS320c6x17 years ago 1 reply

hi all: I have a question about c672x. Can 510 emulator support c672x? Someone told me that C672x need 560 emulator and ccs3.2. Is...

hi all: I have a question about c672x. Can 510 emulator support c672x? Someone told me that C672x need 560 emulator and ccs3.2. Is it true? Thanks! luckeybird


Issue when connecting xds560 JTAG emulator to DM642

Started by karthikeyan B in TMS320c6x16 years ago 1 reply

Hi, I face an issue while connecting xds560 PCI JTAG emulator to DM642 EVM. I've the xds560 emulator inserted in the PCI slot of the PC and...

Hi, I face an issue while connecting xds560 PCI JTAG emulator to DM642 EVM. I've the xds560 emulator inserted in the PCI slot of the PC and installed the driver for it. When I run the diagnostics of the xds560 emulator, all the tests in the diagnostics gets passed without any issue. In the CCS setup, I configured the DM642XDSEMULATOR option and tried opening the CCS. But I get an ERROR mention...


Conceptual question on Emulator and HPI

Started by Anonymous in TMS320c6x22 years ago 2 replies

Hello. I have some conceptual questions on emulator and HPI. What is the benefit of using an external emulator instead of an...

Hello. I have some conceptual questions on emulator and HPI. What is the benefit of using an external emulator instead of an embedded JTAG to perform debugging of a DSP board (with CCS)? I understand from a good friend who has always answered my questions that with an external emulat