DSPRelated.com

DM642 video streaming

Started by Ahmad Mohamed in TMS320c6x16 years ago 3 replies

Hello I have a small project using DM642, 'video streaming using DM642' I am new in this field, what i want to do is to capture a video ,...

Hello I have a small project using DM642, 'video streaming using DM642' I am new in this field, what i want to do is to capture a video , then stream that video using DM642 EVM anyone of you has any idea or resource on this please help me thanks in advance -- Ahmed


DM642 as PCI system host

Started by kalp...@einfochips.com in TMS320c6x19 years ago

Hi, For my new design I am planning to make DM642 as PCI system host. The system will consist of DM642 and USB controller with PCI...

Hi, For my new design I am planning to make DM642 as PCI system host. The system will consist of DM642 and USB controller with PCI interface. As there is no other processor required on board, I want to make DM642 as PCI system host. I have gone thru the datasheet and found out that DM642 does not generate IDSEL and it does not have PCI arbitra


dm642

Started by davi...@yahoo.fr in TMS320c6x16 years ago

hello my question is how to control the dc_port's pins of dm642 when sending data.(Note: these pins are connected to the video port(vp1,2,3 )...

hello my question is how to control the dc_port's pins of dm642 when sending data.(Note: these pins are connected to the video port(vp1,2,3 ) of dm642). how can I achieve this task? please I'm jammed and I need your help. thank you _____________________________________


PCI Configuration DM642

Started by modo270180 in TMS320c6x18 years ago

Hi All, I have read the documents about PCI in the folders of the DM642 in the TI site. But I found some troubles to understand what I should...

Hi All, I have read the documents about PCI in the folders of the DM642 in the TI site. But I found some troubles to understand what I should do for configure the DM642 as a slave and I would like to do some questions: If, the DM642 is a slave, the task of the configuring the registers is make by the master? What are the registers that I (SLAVE) have to configure? Tank you for yours...


Driver Problem in DM642 EVM

Started by Ramanan in TMS320c6x20 years ago 1 reply

Dear Experts, ? 1. We recently acquired a DM642 Evaluation board through TI. Alongwith the Board, we received an installation of CCS 2.2...

Dear Experts, ? 1. We recently acquired a DM642 Evaluation board through TI. Alongwith the Board, we received an installation of CCS 2.2 and the DM642 EVM CD. However, the DM642 EVM documentation mentions that the device drivers & emulator drivers in the CD will work only with CCS v3.0 or higher. Kindly confirm whether this is true. ? 2. Sti


Capture the video from a camera and to display it on a monitor using DM642 EVM board

Started by bharath in TMS320c6x19 years ago 2 replies

Dear all, I want to capture the images using a camera and have to display it on a monitor/TV using dm642 EVM board. My idea to proceed with...

Dear all, I want to capture the images using a camera and have to display it on a monitor/TV using dm642 EVM board. My idea to proceed with this is like below: connect the camera and configure one of the Decoder of dm642(dm642 has 2 decoders). I can choose and configure DM642 using I2C module. The output of the decode will be 4:2:2 YCbCr format. This is given to the video p


Anyone with a DM642 EVM for sale?

Started by jeanpierrepoulin in TMS320c6x20 years ago

Hi! I'm looking to get into the wonderful world of DSP-video by studying the many samples and appnotes (link below) for the...

Hi! I'm looking to get into the wonderful world of DSP-video by studying the many samples and appnotes (link below) for the DM642. Does anyone have such a board for sale? Any advice on where I could find one 2nd-hand somewhere on the net? Many thanks! Jean-Pierre DM642 appnotes:


DM642 developers out there in Bangalore

Started by andyboy26 in TMS320c6x20 years ago

Hi Experts, My name is Anand and I am a rookie in DM642 development. I would like to know of any DM642 developers based in Bangalore or...

Hi Experts, My name is Anand and I am a rookie in DM642 development. I would like to know of any DM642 developers based in Bangalore or in India that might be generous enough to give me their phone numbers. Being a novice, I sometimes get stuck with simple settings for hours together which I could avoid if I could call up someone with more experience.


Difference between C6416 and DM642

Started by qing_lee73 in TMS320c6x20 years ago 10 replies

Hi group, Here comes my second question today: what is the difference between DM642 and C6416? I know there is coprocessor...

Hi group, Here comes my second question today: what is the difference between DM642 and C6416? I know there is coprocessor that deals with entropy coding and some additional peripherals in DM642. But I want to know how much it can help to improve the performance?


Re: Fw: DM642 VideoPort: VP_open doesnt return

Started by mens...@hotmail.com in TMS320c6x19 years ago

Yes, I have the same problem... reset remains 1. This can only happen when the clock signal is not present... but I have a really good clock on...

Yes, I have the same problem... reset remains 1. This can only happen when the clock signal is not present... but I have a really good clock on my DM642. So I switch-off-on and hope it works again. Maybe it has to do with an old version of the DM642, because the first batches had problems. > > Another thing I found out: > > I extracted the source of VP_open from the csl6000.src with


DM642 32-bit access to SDRAM other 32-bits not used

Started by davi...@siliconengines.net in TMS320c6x17 years ago

Just wondering about a design I recently saw which had a DM642 interfaced to SDRAM using a 32-bit wide data bus. The SDRAM chip only has a 32-bit...

Just wondering about a design I recently saw which had a DM642 interfaced to SDRAM using a 32-bit wide data bus. The SDRAM chip only has a 32-bit wide bus and the other 32 bits of the DM642 are not used. Not sure why it was designed this way as it only going to slow down the EMIF that much more. Can this design work? Is this going to be problem? Any special commands required on the DM642 to s...


Re: DM642 developers out there in Bangalore

Started by praf...@yahoo.com in TMS320c6x18 years ago

Hi Anand, I am Prafull and currently working on DM642 in the company situated in Pune.Though i m also a newbee in this, I d be glad if i cld...

Hi Anand, I am Prafull and currently working on DM642 in the company situated in Pune.Though i m also a newbee in this, I d be glad if i cld help u in any regard. Here is my mobile no. 9860611844. mail id : p...@yahoo.com Pls feel free to call or mail me Thanks & Regards Prafull > Hi Experts, > > My name is Anand and I am a rookie in DM642 development. I would like > to know


Interfacing SDRAM DIMM module to DM642 over EMIF

Started by Gautham in TMS320c6x19 years ago 1 reply

Hello We've successfully built a board based on DM642 and we've interfaced an SDRAM DIMM module to DM642 over EMIF (MTYPE: 64 bit SDRAM). Has...

Hello We've successfully built a board based on DM642 and we've interfaced an SDRAM DIMM module to DM642 over EMIF (MTYPE: 64 bit SDRAM). Has anyone tried this before. I'd like to know if there's any performance hit in using SDRAM DIMM modules versus using a standard SDRAM chips. If yes, how much. We're running DM642 at 600 MHz & SDRAM is configured at 100 MHz. Thanx & regards Gaut


deinterlace on dm642

Started by tras...@82er.de in TMS320c6x19 years ago

hello, i'm using a philips pal camera on the dm642. unfortunately the camera sends interlaced images. does anybody know if there is a way to...

hello, i'm using a philips pal camera on the dm642. unfortunately the camera sends interlaced images. does anybody know if there is a way to deinterlace on the dm642? a standard c-algorithm to deinterlace should be fine as well.. thanks a lot, johannes.


VideoPort of DM642 as GPIO

Started by modo270180 in TMS320c6x18 years ago

Hi All, first of all I would like to tank all the people who helped me in the previus question. I have a problem in the configuration of...

Hi All, first of all I would like to tank all the people who helped me in the previus question. I have a problem in the configuration of the video port of the DM642 in an ours board. I would like to use the low half Video port 0 of the DM642 as McBSP and the high half as GPIO (only pins VCTL0, VCTL1). The aim of this two pins is to control the shift page of a flash memory. Moreover th...


Optimization tips for HEAAC ported on DM642 hardware.

Started by Nilanjan Goswami in TMS320c6x18 years ago

Dear All, I am Nilanjan. I am very new to this group. I need to port a HEAAC decoder on Dm642 hardware. Can you guys tell what will be current...

Dear All, I am Nilanjan. I am very new to this group. I need to port a HEAAC decoder on Dm642 hardware. Can you guys tell what will be current market standard MCPS figure for HEAAC decoder(fixed point version) on DM642. And I also need some information which are the areas I should look first for HEAAC decoder optiomization on the board. I am highly looking forward to yuor reply. Thanking you...


DM642:::video encoder

Started by suren porwar in TMS320c6x20 years ago 6 replies

  Hi All, I just wanted to know whether the video encoder(latest or older version) on EVM DM642 accepts frames in YUV 4:2:0 or...

  Hi All, I just wanted to know whether the video encoder(latest or older version) on EVM DM642 accepts frames in YUV 4:2:0 or do we have to resample it to YUV 4:2:0 from YUV 4:2:2. I referred few documents in TI site  all the examples, using evm dm642 accept YUV4:2:2 and then c


How to enable C64's(board dm642) pci boot mode in linux driver

Started by onlyflyer in TMS320c6x18 years ago 1 reply

Hi: I'm writing a linux driver for C64(board dm642).In order start DM642 in linux host,I do things as follow: 1)warm reset c64 2)init emif...

Hi: I'm writing a linux driver for C64(board dm642).In order start DM642 in linux host,I do things as follow: 1)warm reset c64 2)init emif for dm642 3)mmap the c64's iram to userspace 4)set c64's memory zero 5)load c64's bin file to iram 6)trigger dspint to start c64 BUT,i doesn't work.When i clear the c64's iram, the whole system is crashed. I find that C64 is not in pci boot mod...


The "McASP system clock" in DM642

Started by pan....@zte.com.cn in TMS320c6x18 years ago

Hi all, Could anybody tell what the frequency of "McASP system clock" in DM642. I used to think that was the same as the "AUXCLK". But...

Hi all, Could anybody tell what the frequency of "McASP system clock" in DM642. I used to think that was the same as the "AUXCLK". But recently, I found a sentence written in the "TMS320C6000 DSP Multichannel Audio Serial Port (McASP) Reference Guide"(spru041g.pdf),which said "Refer to device data manual for the McASP system clock source. This is not the same as AUXCLK". While in the DM642...


dm642 project

Started by tuo faith in TMS320c6x18 years ago

Hi all: Recently, i want to develop a 4 channel video data's compression with 4 channel audio data's compression based on dm642, while i...

Hi all: Recently, i want to develop a 4 channel video data's compression with 4 channel audio data's compression based on dm642, while i found that some pins of the input port of the dm642 chip's video and audio is the same. what can i do to realise the video and audio uninterfere each other ? thanks in advance !