Mahdavi- > Best thanks > I did that work through EDMA and using frame sync configuration > and finally i got a good result. i...

Mahdavi- > Best thanks > I did that work through EDMA and using frame sync configuration > and finally i got a good result. i can read from FPGA about > 400MBytes/sec. Ok great! One request -- please let the group know when you solve the p

Does anyone have ideas for my problem. My serious troubble is i am not able to download my code in my sdram by emif. ...

Does anyone have ideas for my problem. My serious troubble is i am not able to download my code in my sdram by emif. According to my board, i think that i configured correctly my board but it is always the same. Please help me to solve that problem. Does any

Hello all, I am newcomer to this post and I need some of your expertise. My overall goal is to use the c6711 DSK evaluation board...

Hello all, I am newcomer to this post and I need some of your expertise. My overall goal is to use the c6711 DSK evaluation board with a D/A (PCM1608 by TI) and A/D (PCM1801 by TI) converter for a high end car audio crossover system with selectable filter coefficients for varia

Hello My name is Tomasz, I have to make a connection between two DSP. I have to do it on two DSK C6711 , EVM 6701 or between EVM and DSK....

Hello My name is Tomasz, I have to make a connection between two DSP. I have to do it on two DSK C6711 , EVM 6701 or between EVM and DSK. I know that the easiest way to do it is by McBSP, but I think better solution is by using HPI and EMIF. Have someone done something like that? Could someone help me how to connect it or show me where can I look for information or examples how to do it? ...

Hi, I was wondering if anyone out there could help me get my DSK's Daugterboard EMIF working for asynchronous memory elements? I...

Hi, I was wondering if anyone out there could help me get my DSK's Daugterboard EMIF working for asynchronous memory elements? I can't seem to get the CE2 signal happening at all. I was wondering what you would have to change in the registers etc. and if there is any tric

Dominic- > thanks for the feedback it it appreciated and you are totally right that > is would have been a good idea to add aditional FPGA...

Dominic- > thanks for the feedback it it appreciated and you are totally right that > is would have been a good idea to add aditional FPGA logic between the FIFO > and the DSP ;), I will take your idea into consideration when a > re-design/hardwareupdate will take place. But for now I am "stuck" with my > current design and I was not intending on spending months on this particular > proble

Brian, I?m slowly getting to the bottom of this, but wanted to bounce this off you to make sure I am on the right track. The...

Brian, I?m slowly getting to the bottom of this, but wanted to bounce this off you to make sure I am on the right track. The crucial issue appears to be WHEN and WHERE to initialize the EMIF registers. First the SBSRAM issue. I think I found a workaround so

Hello: Is there a way to tell using any registers if the DM642 internal PLL is locked, and if it is, at what frequency? There is a problem...

Hello: Is there a way to tell using any registers if the DM642 internal PLL is locked, and if it is, at what frequency? There is a problem with the input clock causing unexpected behaviour of the EMIF (which runs off the PLL) - and I am wondering if this can be caught using any registers. Thanks ~ka

Dear friends, Can anyone tell me how to read the board revision of C6713 from our C file and how to use the version register bits to...

Dear friends, Can anyone tell me how to read the board revision of C6713 from our C file and how to use the version register bits to switch the EMIF setting between different board version. Your help will be greately appreciated. Thanks in Advance, P.Sabapathy

Hi, I am working on a system using C6455 dsk. I need to access some I/O pin to control of 5 digital potentiometer .How Can I use GPIO or EMIF for...

Hi, I am working on a system using C6455 dsk. I need to access some I/O pin to control of 5 digital potentiometer .How Can I use GPIO or EMIF for this aim? I am new on dsp, and i know alittle about it. and I need to do this work. I need a little code for accessing I/O pin. Please someone help me. _____________________________________

hi i'm beginner in dsp and work in project that simulate the UMTS channel. and need to connect dsp(6201) to fpga(spartan 3) via EMIF and dsp to...

hi i'm beginner in dsp and work in project that simulate the UMTS channel. and need to connect dsp(6201) to fpga(spartan 3) via EMIF and dsp to dsp via SPI (mcbsp) now my needed help is that is there any one that do this later please me important notes or probable problem in future. thanks d...@yahoo.com

Hi all, I am reading a 16 bit data from a async memory using EMIF. I need to perform FFT and further procesing based on this. Do i need to...

Hi all, I am reading a 16 bit data from a async memory using EMIF. I need to perform FFT and further procesing based on this. Do i need to ALIGN my data. What should i Write in place of 'constant'? in #pragma DATA_ALIGN(symbol, constant) please reply soon, Pramod Mishra ____________________________________________________________________________________ Luggage? GPS? Comic books? ...

Hello All I'm new to using the TI DSP's and have a Spectrum Digital 6713 DSK. I have a daughter board that has some ADS1626...

Hello All I'm new to using the TI DSP's and have a Spectrum Digital 6713 DSK. I have a daughter board that has some ADS1626 1.25MHz A/D chips, among other things, that I have set in memory at 0xa000... for CE2. Try as I may I can't get the DSK board buffers betwe

hi I want to use a TMS digital signal processor to read data directly from Analog to digital converter. I didn't select the DSP yet...

hi I want to use a TMS digital signal processor to read data directly from Analog to digital converter. I didn't select the DSP yet because i want to read 60Msample/s and performe a simple(not very) actions on the samples. in this point i just want to know if i can choose something from TMS320C6000 family? for example c64x can read with emif with 100Msample/s

Hi all, I've a project in which I'm very short of DSP time. The idea is to preselect DSPs and to overclock them. EMIF stays...

Hi all, I've a project in which I'm very short of DSP time. The idea is to preselect DSPs and to overclock them. EMIF stays at 100 MHz. I want to hear your opinion on this. How much overclocking can be possible? How many DSPs would be good/bad?

I'm trying to run the title board with LCD 2*16 via EMIF. I have the book of Mr. Rulph Chassaing and there is an example with LCD but it doesn't...

I'm trying to run the title board with LCD 2*16 via EMIF. I have the book of Mr. Rulph Chassaing and there is an example with LCD but it doesn't work. I have some experience with programming PIC microcontrollers bud not DSP processor. I know there is a lot of problems with time depandancies but have no idea how to start. Does anybody have any example program which can help me understand it or...

How do we dump the boot code for the first time into Flash for the sake of booting a C6713B processor? What is the actual process going on here...

How do we dump the boot code for the first time into Flash for the sake of booting a C6713B processor? What is the actual process going on here when we using the EMIF boot? The Flash we are using here is S29GL016A. Thanks in advance! - Madhuri A.V.L

Hi.I am trying to use the Emif.So i think that i have to supply voltages to J8 which are 12V, -12V, 5V and GND.do i suppose to use all of the...

Hi.I am trying to use the Emif.So i think that i have to supply voltages to J8 which are 12V, -12V, 5V and GND.do i suppose to use all of the voltages? May you tell me is it true or not?thank you.

I've been working with some boot code that I wrote and it's been working beautifully for months. I basically just opened up the gel...

I've been working with some boot code that I wrote and it's been working beautifully for months. I basically just opened up the gel file to get the needed EMIF values and addresses, then initialized that and did my copying. But now I'm having a problem, and I have no idea why.

Hi, I'm trying to use SBSRAM on an EVM6701 board. When I run a COFF file, linked into SBSRAM, it runs OK under Code Composer,...

Hi, I'm trying to use SBSRAM on an EVM6701 board. When I run a COFF file, linked into SBSRAM, it runs OK under Code Composer, but hangs when I run using the evm6xldr.exe utility. I believe I am initializing my EMIF correctly. Any ideas as to what might be wrong? T