Hi: I am a beginner to development using the IEKC64X board from ATEME. I connected an XDS560 JTAG emulator with appropriate...

Hi: I am a beginner to development using the IEKC64X board from ATEME. I connected an XDS560 JTAG emulator with appropriate jumper settings on the board, which gives the video output and LEDs ON as described on the installation guide. (meaning the hardware is connected

Hi Make and Simon, 1) I think that problem with the connection DSP and Host, via JTAG using TI xds510, is on hardware, because, as...

Hi Make and Simon, 1) I think that problem with the connection DSP and Host, via JTAG using TI xds510, is on hardware, because, as sprs294b, the TMS320C6713B requires that both RESET and TRST resets be asserted upon power up. While RESET initializes the DSP core, TRST initializes the DSP emulation logic. 2) In my design I have tow boards: One with only the DSP and peripherals an...

I'm using c6701 based TI DSP board with JTAG and CCS ver2.0. I'm implementing FX-LMS algortihm;  to do real time debugging I'm...

I'm using c6701 based TI DSP board with JTAG and CCS ver2.0. I'm implementing FX-LMS algortihm;  to do real time debugging I'm trying to use DSP bios, however, I could not make my program run. I compil

I Just started using 6713 DSK. After installing usb drivers successfully, it passed diagnostic test. But in my computer's device manager list i...

I Just started using 6713 DSK. After installing usb drivers successfully, it passed diagnostic test. But in my computer's device manager list i can see XDS 560 PCI emulator as with exclamation mark. What can be possible cause. Actually i can see SD usb based debug tool and 6713 dsk as installed OK. But what is reason for ! mark for emulator? Regards, Nilesh

Hi all, I am fed up seeing this error whenever i load the program.I am using DM642 emulator board.Please suggest something so that i can...

Hi all, I am fed up seeing this error whenever i load the program.I am using DM642 emulator board.Please suggest something so that i can be able to remove this error. Are there changes in memory map,JTAG settings,etc Can't Set Breakpoint: Error 0x00000008/-1076 Error during: Break Point, Cannot set/verify breakpoint at 0x807EB518 Breakpoint Mana

hi, i have a couple of question on boot application development for custom target I have a target which uses 6414DSP. with...

hi, i have a couple of question on boot application development for custom target I have a target which uses 6414DSP. with 256kb flash on emifb and 8MB SDRAM on emifa with CCS2.2 with JTAG interface to burn the code. I need a clairification on my approach.

Hi Friends, I am using c6711 & JTAG. I am having a problem in debugging my code. I am using LOG_printfs() for debugging purpose. But when...

Hi Friends, I am using c6711 & JTAG. I am having a problem in debugging my code. I am using LOG_printfs() for debugging purpose. But when i try to use the message log, it gives an error like : 'CDB file error. The associated CDB file may be missing or corrupted.' Can anybody help me? Thanks in Advance. Dipak Gaigole.

Yes Michael, Now my board is connecting, via JTAG, using the Gao xds510. I was pulldown (by wrong) a EMU pin. I read the SPRA584C Application...

Yes Michael, Now my board is connecting, via JTAG, using the Gao xds510. I was pulldown (by wrong) a EMU pin. I read the SPRA584C Application Report (TI) and revises may design. Thanks. Ricardo ________________________________ De: Michael Dunn [mailto:m...@gmail.com] Enviada: qua 31/10/2007 16:29 Para: Ricardo Jose de Oliveira Carvalho Cc: c...@yahoogroups.com Assunto: Re: [c6x] Er...

dear all, i am now using tms320c6711 dsk board in my student project. i use spp mode to communicate the paralled port to my...

dear all, i am now using tms320c6711 dsk board in my student project. i use spp mode to communicate the paralled port to my pc printer port. it can not initialize the target cpu when i start to use ccs. error-1101 stated that check the target power and jtag

Can any one please guide me how to input data to a MATLAB file, the data supposed to come from the processor acquiring real time data, I...

Can any one please guide me how to input data to a MATLAB file, the data supposed to come from the processor acquiring real time data, I think i need to pass it from code composer to MATLAB via JTAG. but i am not knowing the exact procedure. Thanks in advance

Hi, Using DM642 on custom hardware, all hardware has been tested and verified (External SDRAM/FLASH etc). I have a program that...

Hi, Using DM642 on custom hardware, all hardware has been tested and verified (External SDRAM/FLASH etc). I have a program that runs correctly when loaded via JTAG into RAM and executed in CCS. However when the program is loaded from FLASH (via CE0 boot selection) it does not execute the same. I know the GEL file in CCS helps setup the

On 4/3/08, Nilanjan Goswami wrote: > Hi Mike, > > Thank you very much for your help for DM6446 JTAG problems. > > Currently I am...

On 4/3/08, Nilanjan Goswami wrote: > Hi Mike, > > Thank you very much for your help for DM6446 JTAG problems. > > Currently I am facing a new problem in CCS 3.3 beta simulator for DM6446. > I am trying to run a codec on the simulator. Can you tell me whether a QDMA > implemented code runs on DaVinci simulator(CCS 3.3 beta)? > Here the CPU is waiting for QDMA_I

Hi all, How to profile a c-function in the emulation mode?? I am connected to a custom board thro'h Parallel Jtag emulator. ...

Hi all, How to profile a c-function in the emulation mode?? I am connected to a custom board thro'h Parallel Jtag emulator. In DSP/BIOS user's guide, under STS module it is given that how to use it for profiling. I covered my function to be profiled between STS_set

Hello. I have some conceptual questions on emulator and HPI. What is the benefit of using an external emulator instead of an...

Hello. I have some conceptual questions on emulator and HPI. What is the benefit of using an external emulator instead of an embedded JTAG to perform debugging of a DSP board (with CCS)? I understand from a good friend who has always answered my questions that with an external emulat

Hello Sir, As per your reply EducationalDSP HPI interface card may not be available in college. So though it seems foolish i am asking again...

Hello Sir, As per your reply EducationalDSP HPI interface card may not be available in college. So though it seems foolish i am asking again weather RTDX through JTAG can not do this through log files? This i have not read completly but came across this day back. Regards, Nilesh Jeff Brower wrote: Nilesh- > I am doing host to target communication part of my project.

I have designed a board around TI's C6711. I am trying to perform emulation under CCS 2.20 using the spectrum's XDS510PP emulation...

I have designed a board around TI's C6711. I am trying to perform emulation under CCS 2.20 using the spectrum's XDS510PP emulation POD. The "SDConfig" finds and passes the Jtag chain with results like: ** Emulator Test ** $$ EmuProductName=XDS510PP $$ Emu

I am working on DSP TMS 320C6415 chip on OKI evaluation board.I am writing a driver for that. We have a DSP application "pedi.out"...

I am working on DSP TMS 320C6415 chip on OKI evaluation board.I am writing a driver for that. We have a DSP application "pedi.out" which we load through JTAG and our test program internally calls some api's which internally callr driver routines and communicates with pedi.out.

Dear all, I have bought some boards from sundance comp. SMT310Q : carrier board with JTAG XDS510 SMT361A : DSPC6414 D10 I installed...

Dear all, I have bought some boards from sundance comp. SMT310Q : carrier board with JTAG XDS510 SMT361A : DSPC6414 D10 I installed CCS 2.2 but there was an ERROR : "cann't initiaalizing taget" after that I installed CCS 3.2 (beta 2). in code composer setup were there sundance modules option, but there isn't SMT361A or SMT310Q. I set up it with the configuration file that from sund...

I am using TMS320c6713B custom board along with Spectrum Digital EMulator xds510usb. While Connecting with my custom board using sdconfig utility...

I am using TMS320c6713B custom board along with Spectrum Digital EMulator xds510usb. While Connecting with my custom board using sdconfig utility I got ok results. It can scan pattern and verfiy patterns also . However when i start CCS studio i found a message " An unknown error prevented the Emulator in a timely fashion. " I have checked with Reset also . It seems fine too. I am using TPS70345 a...

i have my own specific board with dsp ti c6713 if i connect to my board with blackhawk lan560 jtag emulator i can send data from dsp to...

i have my own specific board with dsp ti c6713 if i connect to my board with blackhawk lan560 jtag emulator i can send data from dsp to host using rtdx and using high speed rtdx if i replace the modem in xds560r i can only use rtdx the hsrtdx stucks at at postcfg.s62 in the line : ------------------------- HWI_Obj 1, HWI_RESERVED1, 3, _function, _monitor, _addr, _dataType, _oper...